Search results

Hi all, I have a 2002 Mustang GT. What is the part number for the two push pins that hold the front bumper cover on the top, near the headlights? The below shows it is for the bottom air deflector - curious if those will work? Mustang Radiator Air Deflector Hardware Kit (94-04) or what...

I will PM you the VIN - looking at buying a Mazda 6 as a DD. The mileage seems to good to be true, based on the condition it is in, IMO. Thanks in advance!

'87-'95 Heads, Cam, Intake Install Help Checklist and Suggested Parts: Parts are specific for 87-93 although most parts are the same for 94/95. Head Gaskets - ROL-HG32841HR (.039) or ROL-HG32841HT (.045) Lower Intake Gasket – FEL-MS93334 (stock) or FEL1250S Upper to Lower Intake Gasket –...

5spd GT submitted a new resource: '87-'95 Heads, Cam, Intake Install Help - install, intake, manifold, cylinder head, swap, camshaft, HCI Read more about this resource...

5.0L Stainless Steel Lower Intake Manifold Stud Kit (BRAND NEW) - $35 SHIPPED Kit includes: High quality Stainless Steel studs, SS washers, and SS flange nuts (specially designed for increased clamp) - (QTY: 12), pack of antiseize for your SS stud kit + install instructions (torque specs...

If I was able to offer a POLISHED STAINLESS STEEL intake bolt kit, would you fellow stangers be interested in that for $30 SHIPPED? The ARP polished stainless steel kit cost $40 on summit + the added cost of shipping, nearing $50. I would also have a stud kit available as well for ~$50, when...

30 lb injectors (Red), one o-ring missing from when I removed them - $90 SHIPPED 6.200" hardened pushrods from Ed Curtis at FTI (5/16" with .083" wall) - $100 SHIPPED (200 miles on them) These prices are shipping included to your doorstep. PM for serious buyers. I take paypal, cashier's...

Just like the title says, my car runs rough (stutters when under load, pops, etc.), but when it warms up all that disappears. I assume this is related as well, but it will not idle without feathering the gas for a minute or so. After that, it idles like a champ. Timing is 16-17* at idle (spout...

I have been doing a lot of purchasing lately for the stang and was curious on how you guys source the best deals for parts, big or small. I use Google Shopping. It finds the best deals based on hits, then can order them for you from least TOTAL (shipping included) cost. Sometimes the big...

I've made a couple runs at installing my ported Holley SMII on my AFR 185's and I keep running into coolant leaks around the ports and at the end seals. I have never had an issue installing other intakes, but his one continues to give me issues. It also seems to me that it the intake is not...

I pulled the plugs (after it sat for a week) and all looked lean or about where I want it, but #3 pulled dark (not oil), like it was running richer than the others. It does pop when driving around (especially under load). Codes read and I got a 41 (passenger side 02 sensor). What are your...

Does anyone have any ideas where to get a new o-ring for the heater coolant tube on the lower intake? It is leaking at the rotating portion above the nut. Thanks for any ideas.

I just got the car started after a couple years of collecting dust. The car will do one light pop maybe once a minute while idling. It is not "back to back" or on a specific schedule. I had it idling for about 5 minutes and heard 4-5 pops. The CEL is on, but I was wanting to get some...

The previous owner broke most of the vacuum hoses that come off the "tree" off the passenger side fenderwell. Does anyone have a picture of the hose set-up and which one (or describe) they went to? Thanks in advance. 1993 5.0.

I am putting the engine back together and have a black ground wire hanging from the EFI harness (below the salt and pepper shakers) that I am not sure where it originally bolted up to? 1993 5.0. Thanks in advance.

I was putting together the car today and deleted the EGR (replaced it with a 3/8" delete plate) and I now have some problems. The throttle cable/linkage is going to be kinked if I could bolt it to the new location, because the delete plate is much slimmer (binding the long throttle cable as I...

What is the bolt size for the ground that bolts onto the back of the driver side cylinder head? I have a black ground wire (with bolt hole provision) that comes off of the EFI harness and I am not sure where it goes. Any ideas? 1993 5.0

I am getting ready to mock up the Holley SMII on the AFR 185 Comps and wanted some feedback from those who have installed one in their fox. I am getting prepared to minimize trouble spots. Are there valve cover clearance issues? Here are the ones I have: Fuel rail clearance issues...

Is there anywhere I can get a heater tube assembly for cheaper than $100? I would even take a parts store one if possible. 1986-93 Mustang 5.0L/5.8L Heater Tube Assembly by Ford at LRS - Same Day Shipping! Thanks!

I am going to set-up the valvetrain this weekend and I got the Comp Cams 7701 (5.800"-6.800") adjustable pushrod checker. I measured it at 5.764" when it was closed completely. Where exactly am I supposed to measure from exactly? I read the Comp Cams use the gauge length, but I do not see...