Search results

  1. dastang2

    Efi 5.0 in volvo need wiring assistance for ac system

    Hello all, been quite some time since I've been here. I've been working on an 86 volvo with a 5.0 efi swap. I'm trying to get the ac wiring done. On the wot cut out relay, which pin should go to the compressor. I found the black and yellow wire from pin 10 on the ecm that goes to the relay, I...
  2. dastang2

    Looking for the member with the 5.0 volvo

    Hello, it's probably been between 5-8 years since I used to frequent this site. I see a lot of new members and noticed a lot of old schoolers are gone. Anyway, I'm working on an 85 volvo with a 5.0 swap. The owner got the painless harness but it's been everything but for the owner. It was...
  3. dastang2

    new KB forged flycut dished 2v pistons

    i got a set of new KB forged pistons. the have new rings and have been cut for valve clearance. i can't use them because i need to bore the block .020 over. these are .005 oversized and a 17cc dish. i was told the wrist pins were upgraded too. looking to get 600 for them. 281 779 5997...
  4. dastang2

    how to visually tell the difference between 03 cobra crank and stock

    how can i tell by looking at the two. i read the cast crank has seams cast into it and the forged crank has no seams. how else can i tell. i know that some cast iron cranks can be 8 bolts too so that would not be a good way to know for sure
  5. dastang2

    can aftermarket pistons be hypers or are they all forged for 4.6

    there are some pistons a guy has locally but he says they are not forged but they are dished. he also has flat tops. didn't think they made dished hyper pistons.
  6. dastang2

    pics of induction with powerpipe.

    i just put a v2 on my 2000. it came with an anderson power pipe. can i see some pics of how yall plumbed the maf and filter in the fender so i don't have to remove the bumper to change filter.
  7. dastang2

    vacuum functions in boosted applications

    putting a v2 on the 2000 soon. do i need to do anything with the vacuum lines to not send boost to things like egr,emmissions,hvac. also is clamping all hoses nec.
  8. dastang2

    can't get the sound i am after after long tubes

    well ever since the long tubes i put on, any muffler selection i have tried are not loud enough. even ones i have had before are way quieter than before with stock manifolds. i have had pypes and glasspacks before and they sounded good but now too quiet and the packs sounded like shet.i have an...
  9. dastang2

    ran at the track

    i just got back from the 1/8th mile running a best of 8.92 at 77.8 mph with a full weight 2000 convertable automatic with stock gears and street tires. mods are 3600 stall,half of a cai long tubes,no cats, flows,jmod and xcal. also have 18 inch wheels on there. soon to have 4.10s and radials. is...
  10. dastang2

    can i change this with an xcal 2

    hello, i just put a stall in the 2000 and ever since then it starts out in 2nd gear unless i manually shift it. it also shifts way too soon and locks up to soon. can i change this with a tuner to make it start out in 1st again in drive position or is that a custom tune thing.
  11. dastang2

    misfire after intake install(heater hose nipple broke)

    misfiring 4.6 bad head gasket or rings go to this link and check out the thread
  12. dastang2

    99 cobra overheating when getting on it

    there is a 99 cobra motor for sell near me but he said the head gasket is blown because when he gets on it, water gets pushed out and temp rises quick. how easy do these blocks/heads warp and crack. what are the odds that i can just throw gaskets on it and it be fixed. he saids it still runs great.
  13. dastang2

    putting a stall and long tubes on 2000

    i just pulled the trans yesterday. i am putting a 3600 stall and long tubes with o/r h on the car in a few weeks. i the trans has a b&m shiftkit in it and not sure what else has been done. i have stock 3.27's on a full weight convertable. what can i expect of the performance i will gain. i have...
  14. dastang2

    just visiting with pics

    i don't get on stangnet much anymore since i discovered westside mustangs in houston but just wanted to visit with a couple pics. just got new rims. i got the car almost 2 years ago with 41000 miles. since then it has been in a wreck and now has a new hood fender bumper and core support. i put...
  15. dastang2

    problem with classifieds login

    istangnet will not let me login on classifieds. i put my info in and it says login successful but when it goes back to the main classified page it tells me i am not logged in. sometimes it does this in the forums. what is up with that.
  16. dastang2

    which would be best twin t3 or single t4

    i am trying to decide how many turbo's to use. i have this t4 with 1.11 exhaust a/r and intake .58 what kind of performance can this turbo give on a stock lower end (stock forged pistons) 5.0 with nicely ported heads and f cam with 600 cfm carb and torker 2 intake. what kind of spool should i...
  17. dastang2

    91 4.3 blazer idle problem.

    going to look at a 91 4 dr. 4x4 s10 blazer with 4.3 and automatic in a few weeks. he says the truck runs good except when it is put and reverse or 4 wd low the motor shakes at idle. i am thinking a vacuum leak but he said he could not find one. i am going to run a compression test on it as well...
  18. dastang2

    header applications

    can i put headers from a 97 onto a 2000. thanks.
  19. dastang2

    where to put nozzle

    how far in front of the MAF do i need to install the nozzle on a dry setup on a 2000
  20. dastang2

    where does this hose go for nitrous kit.

    i just bought this edelbrock dry nitrous kit used. i don't know what this rubber hose goes to. it has a plastic T on the end and a metal barb in the middle of the hose. it is coming from this regulator looking part. what is this and where does it go. thanks. what is the regulator do.