Search results

  1. M

    strut tower brace

    steeda
  2. M

    strut tower brace

    then you would need 2 people to take it off then? one holding the nut from underneath. How am i going to get to the wheel well with no jack stands or jack. Can i do it?
  3. M

    strut tower brace

    If i remove my aftermarket strut tower brace, do i need to get a realignment? I remember i tried to remove one of the bolts and it just kept turning and turning like a nut was held from underneath. is it easy to remove these?
  4. M

    what part is this off my car??

    It came off my 2000 mustang gt. I wanted to know how much it is worth and what is it?
  5. M

    bleeding brakes

    well they are rounded and wrench side did not work on either side, i tried to use the circle side that acts like a rachet.
  6. M

    bleeding brakes

    i rounded the nuts, they were so hard to loosen even with wd40, the 3/8" flare barely fit on it, i couldnt use a 10mm wrench because how would i tighten it with hose on. So i just put wheels back on and drove car brakes are working fine, a little mushy but who cares, seems normal.
  7. M

    bleeding brakes

    maybe im thinking too much about this. how come every how to do bleeding says to pump 4-5x before opening bleeder and on last one hold down pedal and it will drop down to floor when opening bleeder. I remember i did that on my rear brake before once with a friend.
  8. M

    bleeding brakes

    so what about the 5x pumping then hold the pedal on the 5th and open bleeder slowly, pedal goes to the ground and fluid comes out, then close bleeder when pedal is to the floor? dont i put new fresh fluid in the bottle with the hose so it does not suck any air up?
  9. M

    bleeding brakes

    what do you mean? I pump the pedal 5 more time while the bleeder is open? I thought you hold down the pedal until it goes to the floor, then close the bleeder. I just want to bleed my brakes, i am getting rid of the car, i just want no air in it. I will just put new fluid into the MC with the...
  10. M

    bleeding brakes

    I read that bleeding means flushing the system out until you see clean brake fluid. All I want to do is bleed front brakes, i swapped back to stock calipers and brakes and i replaced front lines. I am just going to fill the MC to the recommended line and then attach the hose to the right caliper...
  11. M

    bleeding brakes

    bump
  12. M

    bleeding brakes

    I will be only doing the fronts because i didnt remove the rear brake lines. So even before starting it i remove the cap and fill it to the recommended line. That should be enough, why would it ever run out of fluid and then suck all the air in. Thats alot of brake fluid. Once you open bleeder...
  13. M

    bleeding brakes

    ok went back to home depot and got the right size. i got 1/4" orginally with a .170 OD, now i got 1/4" with a .375". Thanks you were right :)
  14. M

    bleeder brake hose

    nm
  15. M

    brake caliper bolts

    ok i got them off and put the brakes back on, i tightened the 15mm bolts, do i tighten those 2 1/2" bolts on each side that are on the caliper that hold the slide pins?
  16. M

    bleeding brakes

    So if 1/4" tubing did not work, what tubing do i get to fit? i need something bigger. I need to get clear tubing to fit on the brake bleeder.
  17. M

    brake caliper bolts

    Closed end wrench? the circle part? My wrench is so short for a 15mm, i tried whacking it with the 3/8" rachet with the 1/2" whacking. It didnt move. I dont want to strip the bolt turning so hard.
  18. M

    brake caliper bolts

    I cant get the 2 15mm bolts off the caliper from the spingle on the front brakes. It is literally impossible, I have no leverage. I am trying with a 3/8" driver that is small/short and now Im going to try with a 1/2" driver with a 15mm. I am going to get a 15mm tommorow for 1/2" driver. I got a...
  19. M

    bleeding brakes

    But i wouldnt keep the master cylinder open while im bleeding correct?
  20. M

    brake hoses

    What size vacuum cap do i need to put over it when i disconnect the front brake line so it does not keep leaking brake fluid?
Top Bottom
Back
Forums
Menu