Search results

  1. S

    Stalling problem

    That sounds possible........and yes it was very low before I filled it, but it still stalled. I will take off the belt this weekend and see if that is the problem....thanks.
  2. S

    Stalling problem

    Stalled again....while driving home, everything was fine....while stopped at a traffic light, just to see what was going to happen, I turned the wheel slightly and my car instantly stalled. It started right back up with no problem.....I do want to figure out how to make this stop happening.
  3. S

    Need help getting off tie-rod ends

    I have always used a pickle fork......the last time I was using the fork on a balljoint, and I beat the hell out of it, but it would not break free. I went out and bought a 4lb hammer so I could hit it harder.....it broke free with about 3 hits using the heavier hammer.
  4. S

    Stalling problem

    Come on guys!!!.....I figured out myself what I think may have been the problem......when I would turn the wheel, while stopped, the rpm would drop to below 500 and sometimes stall. I opened up the power steering res and it was extremely low. I had worked on the suspension a few weeks ago, and...
  5. S

    Problem with new suspension

    I installed the same springs a few weeks ago and I am disappointed in the results....the rears look like they sag (compared to the front) and the rear will bottom out from time to time (yes, I installed the small bottom out bumper)......but the fronts look like they have not been lowered much if...
  6. S

    Stalling problem

    Suddenly, my car is stalling, not always, but now and then. If it stalls, it is when maneuvering around a parking lot, or backing out in the morning. It always starts right back up, and shows no sign of a stall when driving, and it will not stall when stopping at a light. Here are the...
  7. S

    How do I remove LCA bolts?

    I did not get to the LCA bolts this past weekend as I had hoped, so I have not had a chance to try to take them out. Yes, I have an air hammer, but I have not used it. I am not sure how to use it cause the stupid thing comes with no directions. I bought a 5 piece set that goes with the...
  8. S

    Eibach springs on crappy shocks/struts

    Apparently this issue has been covered in the following thread: http://forums.stangnet.com/showthread.php?t=447902 This guy was complaining of the exact same thing....oh well....I'm still gonna get some better dampers/shocks.
  9. S

    Eibach springs on crappy shocks/struts

    OK...I give up....I drove it to work this morning and it was like a dune buggy on a flat highway (not literally, but I there was a lot of bounce and It is coming from the rear)....not really a recoil type bounce, I can feel every crack in the road. I pushed down on the rear and it simply...
  10. S

    Eibach springs on crappy shocks/struts

    Thanks for the advice....I won't worry about it, and just start looking for a damper made for an Eibach/lowering spring.
  11. S

    Replacing calipers and rotors - any tips, advice?

    Hmmm...I don't have a Cobra (wish I did) but rotors usually just come off without any effort.....some rotors may have little retaining clips on the studs.
  12. S

    Eibach springs on crappy shocks/struts

    I drove on the new springs for a week with new front struts, without a problem...then this past weekend, I installed the rears and when first driving it, the car felt like I was bouncing down the freeway with every crack in the road. I read on the Monroe website something about expanding and...
  13. S

    Eibach springs on crappy shocks/struts

    Oops..... Oops....I found this on the Monroe website......I used my air-ratchet on the rear mounts in the trunk and my impact on the strut mounts under the hood. I think the fronts are fine, but I may have blown up the rears. During assembly Do not use an air impact wrench as there is a...
  14. S

    Eibach springs on crappy shocks/struts

    I installed Eibach Pro-Kit springs and since I had Monroe Sensatrac shocks/springs I took them in and swapped them for new ones (lifetime warrenty)....I plan to upgrade the shocks when cash becomes available. Now my car rides like a freaking dune-buggy......since my car is lowered, is that...
  15. S

    Need help on front end noise

    I had squeeks, groans, and clunking, and it was extremely embarrassing. I had what looked like a leak in my steering rack, so I replaced that and I still had squeeks. Next I replaced the tie rod ends, and I still had squeeks. Next I replaced the ball joints, and that was the problem....no...
  16. S

    Dizzy Bolt Removal!?!?

    I use a 1/2" open end wrench....you can get to it by going underneath the center pulley...(not when it is running though)
  17. S

    How do I remove LCA bolts?

    I think I figured it out I thought of something I can try to get the frozen bolts to bust loose....(I can get the nuts off, but the bolts won't budge) I could use the ball joint press on the left side(front) bolt and see if that will break it loose....If that works, there should be enough...
  18. S

    Installed Pro-Kit springs...questions and I have a hum noise.

    Yikes.....I have new bushings already from En. Susp, and a torch, but I tried to burn a nut off one time before and all I did was make it red...I end up using a circ saw and a diamond blade and cutting the nut off. I'll try the PB, Liquid Wrench, heat idea and see where that gets me. I...
  19. S

    How do I remove LCA bolts?

    I did not try heat....I was in the middle of doing a complete suspension job of struts (and energy suspension bushings so I had to burn off the rubber thing in the shock tower cone thingy, what a mess), shocks, ball joints, springs, rack bushings, tie rod ends, hmmmm...all by myself and had to...
  20. S

    Eibach spring install problem

    I tried that last night....I unbolted everything....then pushed down on the LCA and could not even turn it....then I had my son stand on the LCA and I turned it slightly, then gave up and I will do it with the spring compressor...it is free to borrow, and I have an impact takes only seconds to...
Top Bottom
Back
Forums
Menu