Search results

  1. Mach1Run

    Which of these lines is for the rear?

    Standing on the drivers side looking down at the proportioning valve with the master cylinder removed. I am suppose to remove the line for the erar but the picture my instruction have is crap and just show both lines without identifying one from the other. Is the line for the rear the one on the...
  2. Mach1Run

    Getting ready to install a line lock

    And I was doing some research. Seems supposedly the easy way is to go from the bottom and remove the line from the MC and the proportioning valve and slide the assembly up. My question, if I unscrew the line from the MC will it drain all the fluid from the MC or just what? Trying to figure out...
  3. Mach1Run

    Lowered today

    wow i would have expected more dramatic drop on a gt. the mach look low 15 min after I put my sportlines on, even more so now they have settled for 2 1/2 weeks. Though I did leave the isos out.
  4. Mach1Run

    Mach 1 Front/rear sways and sfcs

    Stock mach SFC are 1/2 length. Pass on those and get some full length ones. No idea about the sway bars.
  5. Mach1Run

    official 4.6 liter Mustang photo thread

    Best pic of the mach I have gotten to date.
  6. Mach1Run

    Is there a set of springs that do 2" front and 1" rear?

    maybe mix and match a set, someting like sportlines on the front and stock mach 1s on the back? Thats all I did with my mach to get a rake since its already about 3/4 inch lower than a gt.
  7. Mach1Run

    Which CC plates do I need to look at?

    So I finally got around to lowering the Mach a week or two ago with some Eibach Sportlines. At first i thought maybe it would be able to be aligned with the stock plates but after 2 weeks to get them settled its pretty obvious I need CC plates. Question 1: Do I need 3 or 4 bolt plates or does...
  8. Mach1Run

    Mach 1 How many PSI do you think I should run?

    Stock internals go with 8 and leave some room if you need it.
  9. Mach1Run

    bassani catback install question

    To get mine on I used juack stands to support the body and let the rear hang. Slips right over that way. Couldnt get over when I tried it backed up on ramps.
  10. Mach1Run

    Any ideas what would cause this? Vid included

    Mine started dong the exact same ting but only every now and then like once every two weeks. I suspect either issues with the accufab TB or more specifically the TPS since I didnt set it with a meter.
  11. Mach1Run

    Looking for pics of your cars with 2" drop

    Sportlines on the front no isos. May or may not swap in the rears, its kinda growing on me and at least this way I can get over a speed bump with a very minor scape on the midpipe. I am kinda afraid what would happen if I tried to cross one with the rear dropped.
  12. Mach1Run

    Thinking about a mach!

    The bassani X is the same for 5 spd mach and gt. 99% sure anyway. I got 12.5k trade in on a 01 GT with 40k miles on it when I got the mach 3 years ago. I dont think you're gonna get 10k for it but you never know, maybe by private sale. KBB values in my area for example...
  13. Mach1Run

    Well It's Gone....

    Well done you wont regret it!
  14. Mach1Run

    How much should a tune up cost

    Wow for $325 my mach was dyno tuned, plugs changed, and oil topped off.
  15. Mach1Run

    X-pipe question

    Seeing that you are in MD consider your inspection requirements. No cats = no pass if a visual is required. You may be better off to buy one instead of trade so that you can still swap the stocker on for inspection time.
  16. Mach1Run

    4th or 5th for cruising?

    6th :) but I dont really have any hills to deal with.
  17. Mach1Run

    Little get together in Plano (PICS)

    Doh I had meant to go to that meet this weekend but had to go to a nieces 1st birthday instead.
  18. Mach1Run

    Using Predator to check TPS.

    I installed a new TB and occasionally have the hanging idle issue. Normally its a TPS issue. Someone said to use my predator to do it but I couldnt find anytihng that looked like a TPS reading through the menus. Afraid i had a case of Blonde and was missing it.
  19. Mach1Run

    Using Predator to check TPS.

    Whats the best way to go about this? Select Diag mode then start the car, then select which report to get the voltage?
  20. Mach1Run

    Sumitomo Tires - Good / Bad?

    Had them on the back of the mach for a year or so. No bad ford DD, but terrible for playing at the track.
Top Bottom
Back
Forums
Menu