Search results

  1. R.J.

    CJ Pony Parts. Any experience?

    I think they are great. I was in the market for some #24 fuel injectors right around the time they had a HUGE price increase. Everybody knew the new prices but they honored their magazine ad's (which listed the lower price) for the entire month that the magazines was on the shelves. I think...
  2. R.J.

    Squeaking front suspension won't compress

    I would think that your lower control arm bolts were torqued with the suspension unloaded. Try loosening the control arm pivot bolts then jack up that side of the suspension and torque the pivot bolts with the suspension fully compressed..
  3. R.J.

    IAC Restictor Plate???

    The 5.0 and 4.6L restrictor plates are the same. I have one that I can mail you, just PM me your name and address. Every once and a while I make 20 or so of them and give them away. As of right now I have one.
  4. R.J.

    Idle Problem. Please Help!

    Replace your IAC and reset your idle and TPS like this: Begin with a cold vehicle. The idea here is to get the car to a firm cold idle with enough air bleed capacity left in the idle circuit for IAC adjustment. The idle stop should be set first. Back out the idle stop screw, away from the...
  5. R.J.

    drivability problems on a stock motor...

    Check to see if your TPS voltage is low. If it is use this procedure to reset your idle and TPS. Begin with a cold vehicle. The idea here is to get the car to a firm cold idle with enough air bleed capacity left in the idle circuit for IAC adjustment. The idle stop should be set first...
  6. R.J.

    bbk or frpp 70mm T.B?

    Go with the FRPP PM sent
  7. R.J.

    Idle Problem

    When you log on to this forum look at the top right hand side of the screen where is says Welcome, Crazypyro87 You last visited: XXXXXX Private Messages: Unread 1, Read 0 Click on private messages, these will be messages that people can send just to you and not the whole forum.
  8. R.J.

    new clutch making noise-NEED HELP

    No it is not normal, the 25 times it took to adjust is not normal either. You Your crap plastic OEM adjuster id worn. Give Lethal Performance a call and get a Fiore quadrant setup. They are the best of the best and Lethal now owns the rights. 1-877-2lethal Keep the OEM cable, all other are...
  9. R.J.

    Idle Problem

    Yes if you think you have a vac leak, spray the suspect area with starter fluid. If you do have a leak the fluid will get sucked in and the engine will rev up. Did you look at your PM?
  10. R.J.

    new clutch making noise-NEED HELP

    Did you adjust your clutch cable tension? With the stock adjuster this can be accomplished by pulling the clutch pedal aft toward the drivers seat then pushing it to the floor.
  11. R.J.

    Valve or lifter noise on my new engine

    Here is a great procedure for setting your lash, even if you did it correctly sometime it need to be retightened. With the piston at TDC with both valves in the closed position, do the following: The first thing you want to do is verify zero valve lash. The best way to do this is to wiggle...
  12. R.J.

    Idle Problem

    Your IAC is bad and cleaning it might have made it worse. Replace your IAC with an OEM piece and reset your idle with this procedure: Begin with a cold vehicle. The idea here is to get the car to a firm cold idle with enough air bleed capacity left in the idle circuit for IAC adjustment...
  13. R.J.

    Forging a 2v

    As mentioned above, check out MMR. They seem to have the lowest prices. Modular Mustang Racing
  14. R.J.

    Rearend Slop Driveshaft Rotates

    The Mustang drive train does have a lot of "normal" slop in it. Yours sounds excessive and you might want to check you backlash.
  15. R.J.

    terrible idle after install

    The EGR is your problem, you will have to have your EGR shut off with some kind of tuning device or buy the tube extension from 5.0 restoration.
  16. R.J.

    Installed my 70mm Edel Throttle Body (had 65mm)

    Try this, it will fine tune your idle and reset you TPS: Begin with a cold vehicle. The idea here is to get the car to a firm cold idle with enough air bleed capacity left in the idle circuit for IAC adjustment. The idle stop should be set first. Back out the idle stop screw, away from the...
  17. R.J.

    Installed my 70mm Edel Throttle Body (had 65mm)

    Did you check your TPS voltage after installing the TPS on the new T-body?
  18. R.J.

    Need suspenstion bad

    +1 on the bullitt kit from Ford becuasue of your price range. PM sent
  19. R.J.

    Car won't Idle, and dies.

    Both adjusting screws are on your throttle body, is it one of those that is stuck? If you can get them unstuck I would replace your IAC and reset your idle and TPS with the following procedure. Begin with a cold vehicle. The idea here is to get the car to a firm cold idle with enough air...
  20. R.J.

    Refilling Steering rack and Pump

    You only have to turn it by hand until the system will not except all of the fluid in the reservoir. At this point when you start it the reservoir does not empty and air fill the system. Now you let it run and slowly fill the reservoir till it stays full.
View older results
Top Bottom
Back
Forums
Menu