Search results

  1. 9

    Next Mods to Crack 300 RWHP

    well the car is a daily driver with stock internals, so it would never see anything close to 6400 rpm. I'm guessing with my current mods I would see 25-30 rwhp out of them?
  2. 9

    Next Mods to Crack 300 RWHP

    Well if I were to do TFS heads and cams I would be close to what a used blower costs. I'm just looking to get over three hundred without breaking the bank. Can the stock motor run any of the stage II heads without springs? I read of a guy who used the comp cams 270's with stock...
  3. 9

    Ebay Short Throw Anyone?

    Dude, take it from me, cheap parts are a pain in the a$$. I have chepo headers, mid pipe, and a pypes exhaust. none of it fits right. The steering shaft touches the headers so i get engine noise inside the car and notchy steering in reverse. We had to dent the floor pan to make room for the...
  4. 9

    Next Mods to Crack 300 RWHP

    I am looking to break in to the 300 rwhp club next year. Car and Mods: 2002 GT Long tube headers, catted x pipe, cat back 3.73 gears I had the LT's installed this summer and the shop got a basic tune in for the gears and new mods, but couldn;t do real tuning since, as it turns out...
  5. 9

    Headers Banging, so which Motor Mounts?

    Got a ballpark # of about 180$ since the headers are on. What do you guys think?
  6. 9

    Headers Banging, so which Motor Mounts?

    Yeah, I wouldn;t htink twice about doing the work myself exceot for the headers. Can anyone chime in who has done the motor mounts with headers installed? Also, while I'm at it, should I do transmission mounts too? I saw summit has an enery suspension set with both. :shrug:
  7. 9

    Headers Banging, so which Motor Mounts?

    So I thought there was an issue with the new terminator clutch because once it went in this popping and squeaking started up as the clutch engaged in 1st gear or on hard shifts. I got under the car yesterday and saw a spot where the drivers side long tube was banging against the floor pan. I...
  8. 9

    New 03/04 Clutch IN GT Rattle

    Well I installed the Maximum Motorsports kit including the factory cable, firewall adjuster, and clutch quadrant. It made a signifigant difference and the clutch pedal has good feel. However, I still get the noise when I first start driving around, then after a mile or two of driving and shifts...
  9. 9

    New 03/04 Clutch IN GT Rattle

    bump. Could it be the throw out bearing retainer?
  10. 9

    New 03/04 Clutch IN GT Rattle

    Anyone? Help? Also, when the car is in first/second gear, and I let the car coast, then get on the throttle, the rattle happens then too sometimes...What gives? I contacted the shop that did the install and they suggested Steed's adjustable cable/quadrant/firewall adjuster. Will this...
  11. 9

    New 03/04 Clutch IN GT Rattle

    Ok, so the noise is still there. I checked the shift fork cover, secure In neutral no whine, so not the TOB(new) Engagaed, no noise, so not the pilot bearing(new) No noise from the tranny To describe the sound, it sounds like somthing hitting something and grabbing. Sometimes a...
  12. 9

    New 03/04 Clutch IN GT Rattle

    I will give that a whirl and let you know. I fired the car this morning and i rattled at first, then stopped by the time I hit the end of the street. I don;t think it is the TOB because it is not a grind or a squeel. It's a mechanical or impact sound, not one due to friction. I will...
  13. 9

    New 03/04 Clutch IN GT Rattle

    Exactly, the klinking occurs as the clutch is let out. It literally sounds like something loose rattling around. Once the car is moving it doesn;t make the noise anymore. When I go into second sometimes it makes the noise. But after five minutes of driving the noise dissapears all together...
  14. 9

    New 03/04 Clutch IN GT Rattle

    I would assume they did. What is throwing me is that the sound goes away after a few minutes of driving. :shrug: What else could be causing the sound?
  15. 9

    New 03/04 Clutch IN GT Rattle

    Bump.
  16. 9

    New 03/04 Clutch IN GT Rattle

    Rattle from New Clutch in First Gear So I had a new clutch put in recently. It is the 03 Cobra clutch in a 2002 GT. Had the fly wheel resurfaced, new clutch fork, pilot bearing, and throw out bearing installed. I am a little over five hundred miles so the clutch is about broke in. I am...
  17. 9

    03-04 Cobra Clutch in GT

    bump. Do I need to get an adjustable pivot ball or should I get a factory replacement? The cobra clutch just came in so I just need to order the rest of the parts for install...:nice:
  18. 9

    03-04 Cobra Clutch in GT

    SO which one of these do i need to get? pivot ball - Clutch Pivot Ball - 4.6L / 281in - JEGS High Performance
  19. 9

    03-04 Cobra Clutch in GT

    So should I just get a factory replacement cable from the dealership and call it a day? I am thinking this is my list of parts to order: 2003 Cobra Clutch FMS Nodular Iron 21 lbs. flywheel Factory clutch cable TOB Pilot Bearing Optional: MM F/W adjuster and quaddrant While I'm...
  20. 9

    03-04 Cobra Clutch in GT

    That is awesome to hear. I like staying with Ford when I can for the driveline. What does everyone think of the Max. Motorsports clutch quadrant/adjuster w/ the factory cable?
Top Bottom
Back
Forums
Menu