Search results

  1. forpit2000gt

    Bolt on header stripped...

    Go to a NAPA store or call and use this number, 600-1819. I think that is correct. I will check again to be sure.
  2. forpit2000gt

    Gears Vs.Revs

    98 v6 rearend is 7.5. not 8.8.
  3. forpit2000gt

    p0355 - ignition experience then come in

    A scanner should show which cylinder is missing if it is a COP. Sounds like a PCM problem. Does the car have a chip in it? Any tuning?
  4. forpit2000gt

    Diablo Chip

    10rwhp
  5. forpit2000gt

    quick lug nut question

    if racing that is true, most tracks don't do a lot of checking around here unless sub 11s. The longer studs are better and not very hard to install. Jim, did you have to use spacer on the rear or just the front? I only had problems with the front.
  6. forpit2000gt

    Back from the track... And now in the 12 sec club!

    does the car have the factory springs and shocks all around? I said before and will again, If those are are the timeslips, your engine is modded more than you know. It is possible to get to 12's without cams but requires weight savings and a very , very good driver. You would have to power...
  7. forpit2000gt

    Bolt on header stripped...

    that stud can be removed and replaced with the stud kit from Napa. You may or may not need a shop to do it for you. That depends on the tools and mechanical ability you have.
  8. forpit2000gt

    Gears Vs.Revs

    there are 600 threads on gears and what is my rpm with 4.10s and I 'm scared to go with 4.10s should I do 3.90s? If you do one search, all can be answered. :nice:
  9. forpit2000gt

    kenne bell vs. vortech

    if you call MPH and tell them what you are looking to do and power range they will give you the best info, and pricing for what you want to do. My comment about Steada isn't to say they are crap, only that others do it as well or better for same or less money.
  10. forpit2000gt

    Gears Vs.Revs

    what engine is in the car and who said you had 2.73 gears to begin with?
  11. forpit2000gt

    Bolt on header stripped...

    It is just the stud then? is there a bolt head on the back side or can you tell
  12. forpit2000gt

    Ticking sound on throttle...

    it is a ticking or rattling? what year?
  13. forpit2000gt

    kenne bell vs. vortech

    I would look other than Steada. MPH :nice:
  14. forpit2000gt

    quick lug nut question

    http://www.jegs.com/cgi-bin/ncommerce3/ProductDisplay?prrfnbr=4048&prmenbr=361 here is another, is there a performance shop near you? They usually have them. Don't get the Allen head ones. Weld ligs would need to be 1/2 x 20
  15. forpit2000gt

    quick lug nut question

    They are about 2 1/4 inch long, 1/2 x 20. AZ has them. make sure you get washers as well. Or get the lugs from where you purchased rims.
  16. forpit2000gt

    Back from the track... And now in the 12 sec club!

    If those are your timeslips, then your car has more done to it than you know. You will not pull 1.8x 60s and run 8.2x-8.3x in the 1/8 without something helping. Not just tune and suspension. Even with tracrtion, that will slow you down a little because of bogging. Your can must have internal...
  17. forpit2000gt

    Back from the track... And now in the 12 sec club!

    you mentioned in a previous post that time was with , 4.10, exaust, ET Streets and Predator tune. No race gas. Race gas will not help you anyhow, with your setup. I have already said , I believe that it can be done with a very good driver. Prove it to me and everyone else. Take the video...
  18. forpit2000gt

    My fuel pressure gauge on my a pillar

    go ahead and pull the pins. If they are messed up on removal, AZ has them or most any parts store. You may try just rotating the guage and pulling it, it may come out depending on how the wiring is routed. This is something that is not to hard, but if not completely comfortable, do like...
  19. forpit2000gt

    Back from the track... And now in the 12 sec club!

    take that stuff to the track so you will be around to post.
  20. forpit2000gt

    Cooling problems

    are you sure it isn't full of air?
Top Bottom
Back
Forums
Menu