Search results

  1. Mustangless

    spark timing tables and power adders

    Settings all other spark tables to 55 will ignore them. On the base spark table I have the top 2 rows from 2000 up at 19*. So it just locks at 19* with enough throttle. I still get it pulled when it warms up enough though. I don't have n20 so I am not really sure, but it should be the same...
  2. Mustangless

    lambse, kams... rich?

    Found where the antifreeze is coming from. Its the where the line goes in about 5" below the cap. Pulled the hego out and replaced it with the one I though was messed up. It was still messed up, but I found my other one I had. It only has 1k miles on it. Pulled the drivers side header and...
  3. Mustangless

    lambse, kams... rich?

    I hope its not a blown gasket, I have only seen 4lbs a couple of seconds this last week, no WOT. Looked at my dipstick yesterday and it was pure oil. My wideband was showing 10.7-11.3 during one of those runs. But I have not looked at the wideband since then. During that time the o2 seemed...
  4. Mustangless

    lambse, kams... rich?

    Just did a log after driving some. All what I have is bad news :nonono: 1. Fans run more than I think they should (never noticed this, but they run alot). Looking under the hood I see some antifreeze on the drivers side radiator. Looking under the car (more about that in a second) and I...
  5. Mustangless

    Finished the interior conversion

    is that a DIY seat delete? if not, who made it and how is it?
  6. Mustangless

    lambse, kams... rich?

    I have not drove it yet, but I did reset the kams (don't know if I should have with just inj. slopes). Started it up and let it idle. Lamse was 14.xx in OL, the it went to CL, and it dropped to low 11s high 10s and went right back into OL. :shrug: Waited a while and it never went back to...
  7. Mustangless

    lambse, kams... rich?

    changed my slopes to 42/44.94 and breakpoint 1.65999. I also changed my injector offset vs battery voltage to what yours is, and put in my maf transfer you sent me. (stanger007) Reset kams and drove for a while. Later when I got in I did a datalog. Put my info into EA and it said to change...
  8. Mustangless

    Owned. Heads lifted. Pics inside. :)

    hmmm, Innovate wideband not working :doh: Was this still with 13ish psi?
  9. Mustangless

    lambse, kams... rich?

    sent you one back, but let me say this. When I do the maf curve with EA it looks like what I think it should be, except it goes from 0.0271 volts to 0.75 volts I think that is why it runs so bad.
  10. Mustangless

    lambse, kams... rich?

    Well, let me try to start over with my maf curve Can somebody convert it for me? kg/hr 1280.35 909.79 529.91 322.35 185.49 109.93 65.43 37.84 20.69 volts 4.1122 3.5810 2.8571 2.2799 1.7776 1.3719 .9988 .6460 .3521 I don't think caledit is giving me the...
  11. Mustangless

    lambse, kams... rich?

    got the curve. and I am trying to take in all that information above. I will have to read into all the injector stuff. Never really looked at it before. and i have the flow sheet
  12. Mustangless

    lambse, kams... rich?

    I richened my curve 2% all the way. On the newest datalog I noticed. During light throttle my lambse is 11.7-14.0 and kam is almost always above 1. But up to 1.09. When I am about .5 throttle my lambse will be 11.2-13.65 kam 1. i still feel like an idiot trying to understand all this...
  13. Mustangless

    show your overflow tank

    I like all those, especially moostang's, but the price on the other one looks good. I don't know why I said stock location, I don't want it there.
  14. Mustangless

    show your overflow tank

    What is everyone using for an after market overflow/catch can? I have read that you can use the windshield washer fluid holder, but I still want to keep that. I just want something smaller, that mounts in the same location
  15. Mustangless

    4r70w from a sixer

    http://www.tccoa.com/articles/tranny/index.html# then select Modifing Valve Body to Jerry's specifictions - Jerry's mod You can search on corral.net too. I got some information from there.
  16. Mustangless

    lambse, kams... rich?

    NM, I messed up my MAF curve
  17. Mustangless

    converter needs to be restalled?

    I am looking at sct tune 18 I got a few questions, but I will just ask one. When it locks in 2nd at 600&1020 TP, its 35mph, but it also unlocks at the same TP and MPH? Does this not make it keep locking and unlocking?
  18. Mustangless

    converter needs to be restalled?

    I have been using the same transmission settings that I first got from you. At Tp 1020 it locks at 127. Your tune from the track shows it locking at 65. Guess I will have to tweak with that.
  19. Mustangless

    converter needs to be restalled?

    I got my torque converter when my car was stock. It did good, with little slip (4-6%). Now I have started to notice that it is slipping more. The car used to be at 7psi, but yesterday it was more like 9psi and the slip was bad. Around 5k, I am calculating about 15% slip. I might not even...
  20. Mustangless

    lambse, kams... rich?

    Here is the curve http://eectuning.org/node.php?rid=80 I don't have the bin on this computer. I will have to try messing with the filter part on EA yea, I had just cleared them. I did not think about it relearning.
Top Bottom
Back
Forums
Menu