Search results

  1. QUIKSVT

    2 HEAD GASKETS BLOWN.....WHAT GIVES??

    I think some of you missed the point sbftech made. He did not say to run better head bolts, he said run head STUDS...
  2. QUIKSVT

    My GT goes under the knife...

    Steves a redneck. AWESOME!
  3. QUIKSVT

    Problem or Normal?

    I've never seen one anywhere else? They bolt to the side of the TB, they have to be there to allow or disallow airflow around the butterfly to maintain idle.
  4. QUIKSVT

    flows or race bullets?

    I have o/r H and 2 chambers. loud enough, raspy enough, and deep enough for me... I don't know if I could stand it any more throaty or loud.
  5. QUIKSVT

    Problem or Normal?

    I've had the same problem. Its the IAC as stated above. In my case, it did the exact same thing right before it completely crapped out and would then just idle at 1800 rpm. I think the heat, or something causes them to lock up in the open position. Try spraying it out with carb cleaner. If that...
  6. QUIKSVT

    Is this setup too much?

    Make sure the blower is OK. shouldn't be any play or slop if you give the shaft a little wiggle. Make sure it spins freely, listen close for bearing noise. Don't mistake it for gear noise though. Depending on the crank pulley size, which should be 8" I think. you could run a 3.3 pulley which...
  7. QUIKSVT

    E-cam good enough for vortech s-trim

    There is better cams, Steeda makes a nice dual pattern that would be better. Steeda 19, I think. 480 lift w/1.6s should be 510ish with 1.7s. 220/226 and 112 or 114 sep. E cam would net you more lift, but its a single pattern cam.
  8. QUIKSVT

    Aftermath of my brother stealing my car. DIALUP WARNING

    I would just walk around, and everytime you see him, or walk by him in the house, pull out some pepper spray and blast him... Real casually... Spray and walk away...
  9. QUIKSVT

    Stock Car Slicks = FUN

    Atleast someone gets it..
  10. QUIKSVT

    Stock Car Slicks = FUN

    http://www.youtube.com/watch?v=MvdLkeaATPg Had a little fun on a Late Model Goodyear Eagle slick. Vid quality is bad, it was too dark, but you get the idea...
  11. QUIKSVT

    AutoMeter Clock Pod

    OK. I did some more looking around on Autometers site, and found that as stated, it is supposed to come with brackets. I ended up fabricating my own. Thanks for the responses.
  12. QUIKSVT

    AutoMeter Clock Pod

    I just picked up an AutoMeter 2-guage pod that replaces the clock. Was it supposed to come with supplied brackets? All I got was the plastic surrounding with no provisions for mounting it. Pics? Anything?
  13. QUIKSVT

    2000 suspension in a fox

    it will raise the car an inch at least.. front or rear springs.. but either way the car will sit like a 4x4.. if anythign cut 3/4 of a coil to drop the spring height to the stock fox length... or take out one stock spring and cut the 00gt spring the same height.. and yes the 00gt springs are...
  14. QUIKSVT

    How good is the stock cam?

    i second the b41 or the stock cam with 1.7s
  15. QUIKSVT

    Dart v.s World...Better Block?

    Haha.:D Yea. Stock long block. And I pulled those 1/4 times on V6 wheels and tires.
  16. QUIKSVT

    Dart v.s World...Better Block?

    yes.. you will.. the dart sportsman block is cheap.. and will do what u need it to just fine..
  17. QUIKSVT

    Compression for blown 331 Q

    i would say 9 ;1
  18. QUIKSVT

    missing when hot

    just out of the blue.. what are you running your timing at???
  19. QUIKSVT

    how hard is it to change the oil pan

    yeah.. but dropping the k-member is a PITA to tackle in your driveway
  20. QUIKSVT

    I know better dangit!!!

    Sir, the meaning of your post is unclear.
Top Bottom
Back
Forums
Menu