Search results

  1. D

    grinding noise?

    If it's the caplipers sticking you'll have to replace those pretty much in order to solve your problem. If you've been driving around with them sticking then you might of already warped your rotors and pads from the excessive heat generated. Jack up the front end of the car and try to spin...
  2. D

    grinding noise?

    wheel bearing going bad possibly. if it was brakes it'd be sluggish taking off and want to stop quickly on it own or pull one way or the other if sticking.
  3. D

    Just got my y2k Cobra R HOOD today, Awesome fit, questions inside!

    If I remember correctly his CAI was located directly below one of the vents and the water was going directly on the filter.
  4. D

    Steeda Weight Jacker Billet LCA - How To Adjust Height When Installed?

    never seen a pair of them in my life in person but from what I read there's a 1/2" say socket you use to raise or lower the spring seat area.
  5. D

    another common question, sorry guys

    Like ADRENLN said that's the way to figure it out. Just another way to get overall diameter Example: P245/45/17 245x0.45x2 = 220.5 220.5/25.4 = 8.68 8.68+17 = 25.7" if you round to tenths of an inch. 25.7 is measured on a 8.0" wide wheel. If you streched the same tire on a 9"...
  6. D

    Jba Header Stangnet Group Purchase

    I'd say I might but they don't make any headers for my car so their tech line says. 97 GT? They said my car has air induction on the manifolds.... smog pump? But yet I don't see anything hooked up on the front of the manifolds. I've also read that my car for the transmission is mechanical while...
  7. D

    I wanna Buy Some HIDs...but

    What do you mean add a diode to the kit wiring harness?? It's easier to ask and understand from someone other then an instruction manual.
  8. D

    A Front End Issue?

    There's several things it could be. You could have a bent wheel, the tires could be out or round, slipped belt, broken belt, buldge in sidewall of tire. Did the place that aligned your vehicle take the time to shake down the front end to see if anything is bent, broken, loose? If you have a tie...
  9. D

    Clicking noise coming from front wheel when moving

    Jack up the front end, grab the side of the tires and see if there is any movement from side to side. Take a pry bar if your on a drive on rack or just jacking up the one side of the vehicle. Put it under the tire and see if there is any latteral movement which would be a balljoint. If you have...
  10. D

    Clicking noise coming from front wheel when moving

    it sounds like a wheel bearing is going bad. Most of the time you won't be able to hear it if it doesn't have a load on it.
  11. D

    Getting longtubes..SLP/JBA worth the money over BBK?

    In MM&FF magazine, can't find it right now, on an 05 they were doing kooks, bassani, and one other one in a couple of their magazines with LT's and their matching counter part showing the gains. There was maybe a 2-3 hp difference between the different brands at tops.
  12. D

    lONG TUBE HEADERS???

    where do you find kooks headers for mustangs to buy? I've looked around and haven't had much luck finding anything.
  13. D

    X-cal 2 for 97 GT..

    If your's is a mechanical speed gear then did they mess up on mine then? Cause my 97 GT is an electrical speedometer. My tranny does have a spot for a mechanical hookup on it.
  14. D

    Shift points with 3.73??

    If you wern't reading or can't seem to understand.... he was asking if top of 1st is 33mph, top of 2nd is 58, top of 3rd is 79, top of 4th 100. I don't get how you could think he was saying 1st starts out at 33mph when we all know from a dead stop your at 0mph. and how do you figure that...
  15. D

    problem and confusion..

    where does the rubbing sound like it's coming from? Does it driving straight, only turning? does it get louder when turning? it could be a wheel bearing going bad on ya and sometimes it can be interperted(sp?) as rubbing cause of a hollow growl. Should see if it does it turning left or right and...
  16. D

    Borla Exhaust

    It looks like the borla stinger exhaust is only for 99+ cars..... As for being smooth... I guess I'm mainly looking for is something that doesn't sound really raspy and have a bad drone to it. I'm wanting to lose the stock midpipe at somepoint and was looking to see what might sounds nice...
  17. D

    i need idea(rant really...)

    Funny thing is Sears owns NTB. :rlaugh:
  18. D

    Tuned by the best!

    If your going to max out the 1.7kb then why not just go ahead and get the 2.2 for the difference in money so if you decide to go for more power someday you won't have to spend more money buying another new KB? It's our car, I'd just go with the bigger one for the time being cause there's more...
  19. D

    i need idea(rant really...)

    I work at a sears here in Iowa. We've aligned vehicles that are lowered. We had to use the truck rack to a lowered mustang on there due to it having a longer ramp to drive up. If he would of been any lower then we might not of been able to do it unless we try to buy some long planks for cars to...
  20. D

    Which hand held for a 97 GT

    I have a 97Gt also and I've been looking at them but I can't seem to find one either. Diablo says they make them for 97 also, but can't actually find one that's listed for the car. Is there any that will work?
View older results
Top Bottom
Back
Forums
Menu