Search results

  1. C

    wont shift at high rpm

    that could be it my car is far from stock(360 rwhp). i thought it did this brand new but that could have been the shifter binding up.
  2. C

    wont shift at high rpm

    my 05 wont shift above 6k, its like somthings blocking it, but when it drops down around 4500 it slips right in. it did this with the stock shiffter so i got an mgw and it still does it.
  3. C

    Clutch question?

    tell them to bleed it, its a pain i did mine when my intake was off and it was still hard to get to it seemed to help alittle
  4. C

    ZEX NITROUS KIT USERS

    autolite hto is a heat range lower but check with zex first expect to pay around $80 a set
  5. C

    Is 400rwhp possible

    137 rwhp over stock would be a major accomplishment good luck!
  6. C

    Is 400rwhp possible

    my best pull was 357rwhp and 334 rwtq thats with ported heads, cams,vct deleted, manley rods,cp pistons high but streetable compression, full mac exhaust, aftermarket fuel rails, ported and gutted charge motion plates. i still run stock injectors,throtle body, pulleys,coils, drive shaft. heads...
  7. C

    FUEL PUMP

    i have ported heads cams and etc and i still run stock pump and injectors with no problems
  8. C

    How to get to 400+ NA??

    my car makes 357hp na and yes thats cams, p&p heads, valves, and forged bottom end. champion racing did the heads, boss 330 put it all together. we built it for nitrous to
  9. C

    FORD GT replica wheels for Mustang!!!!

    i emailed them last week and they said only chrome and 18'' for 05s . i too like the gunmetal, with a nice wide polished lip or why dosn't someone make 20'' fr 500s. it seems like all the aftermarket companies are competing to bring out new crazy ideas (body kits and drifting stuff) and there...
  10. C

    Colder Heat Range Spark Plug

    you can get them at napa (on order) there the autolite ht0, unless your saleen already has them then goodluck!!
  11. C

    Considering Cams

    havent noticed any vacuum problems and in town i get 18 mpg 21 hwy thats with a 410 gear, i would like to go 430 (na) to keep it up in its power band but im sure that would be to much on spray
  12. C

    Considering Cams

    im very happy with the work i had done at boss 330 and the head work at champion racing heads they put together a great combo that was designed for the drag strip but my wife can still drive it, so yes it very streetable. i plan on spraying a 175 to 250 shot depending on tunning etc. so far with...
  13. C

    Fiz vs Spec allum flywheels

    nothing you can even use an 04(6 bolt) which is lighter if you shim the throwout/slave cylinder they will give you one with it, and gives you more pedal
  14. C

    Considering Cams

    i had cams pistons rods heads everything done on mine at boss 330 and champion racing heads it sounds mean and pulls real hard to 7200 it put down 360 na 355tq on a realy hot day that took an hour to get to
  15. C

    Do you have to blow?

    i have a completly worked 05 cams pistons rods heads everything, i plan to put nitrous on it but its still a n/a comb it runs great i turn it about 7200 and it loves it on just a quick tune, heat soaked and 120 deg. (in miami) it put down 360 hp , 355 tq
  16. C

    anyone change to a lighter weight flywheel yet ?

    i have a spec alu. in mine and the driveability has not changed ,you can also use a six bolt out of a 04 back gt you just have to use a spacer behind the slave cylinder because the 05 flywheel is thicker (also heaver)
  17. C

    WHERE IS THE NEXT 30HP???

    contact Al at boss 330 racing he just built an entire nitrous 3v for me including CAMS!!! yes there regrinds but still very agaressive
  18. C

    will a 6 bolt 04 gt flywheel fit an 05

    i bought a spec alum. flywheel from a spec dealer at the nmra season opener. its realy for an 04 gt, they say it will work and gave me a spacer for the slave cylinder to raise the pedal (throw). i just wondered if anyone else has been this down road since they do make one 05 specific, but claim...
  19. C

    Pics of my new Turbo motor built by Boss 330 Racing

    how difficult was it to install that one piece driveshaft? im gonna have an aluminum built because i cant afford the carbon fiber
  20. C

    single piece carbon fiber driveshaft

    is it for an 05 or an sn95 my only thought is the lenght since the incressed wheel base, or did they cut it to fit
Top Bottom
Back
Forums
Menu