Search results

  1. bubba-dough

    MSD 6AL - how to convert box from 4cyl back to 8cyl?

    Glad you were able to get her goin'
  2. bubba-dough

    Buyer beware: My buyfordracing.com experience...

    Ok, don't get me wrong here, I am not taking away from your experience, but how is this sticky material???
  3. bubba-dough

    wheel bearings

    Wheel Bearing Front - Advance Auto Parts O'Reilly Auto Parts - Results for Shopping Search
  4. bubba-dough

    computer question

    Just be aware that even with the same mods on car "A" & car "B" they "react or build power" differently (and were tuned for that specific application accordingly), even if said parts are taken off car "A" and installed on car "B". Plus add on differeces in sensors, age of other components...
  5. bubba-dough

    wheel bearings

    If your running the 87-93 stock style spindle a bearing is $12 and takes about 20 min. to change. If you are running 94-95 spindles its about $80. Check your front u-joint as well. Sometimes they squeak as they go bad and the origin or the squeak is hard to narrow down due to it only...
  6. bubba-dough

    Top End Swap Questions (H/C/I)

    PBR :rlaugh: The Trick Flow kit is a good kit. It does not come with lifters so keep that in mind. Its not a horrible job but it is a pretty big project for the beginner. Goodluck.
  7. bubba-dough

    T-Tops?

    I wanted to select 3 of the 4 options you have listed. Take the tops because you better believe the next guy will!
  8. bubba-dough

    new member 1st post w/video

    :welcome:
  9. bubba-dough

    Stickers, . . .Yay or Ghey?

    I only put stickers on @ the track for contingency $$.
  10. bubba-dough

    MSD 6AL - how to convert box from 4cyl back to 8cyl?

    Correct but incorrect - it is rev limiter calibration, but it has to be set back to 8 cyl. for the ignition to operate correctly or you are going to have "rev limiter problems" because the box thinks its on a 4 cyl. The guy cut both wires because it was a 4 banger. Its nothing a lil solder...
  11. bubba-dough

    It Must Be Welded Shut

    iirc you can still take the door panel off from the inside, although its tight as hell, then you can get to what you need.
  12. bubba-dough

    headlights

    1 piece smoked for a black car
  13. bubba-dough

    Whining/whistling noise after throttle body install..?

    Sometimes it happens. It sucks. I have the same problem on my dd.
  14. bubba-dough

    new pics, stance!

    lilbluenotch, but your car is black........:D
  15. bubba-dough

    new to the mustang world

    :lol: Plus about 10 stickers.....:p
  16. bubba-dough

    ran my car

    :nice: Good times. I am itching to go to Indy for a 1/4 mile track (April 21 - Street Legal Drags open up)....stupid southern Indiana loves the 1/8:nonono:
  17. bubba-dough

    new to the mustang world

    Welcome. There are lots of ways to get there, but the budget is the determining factor.
  18. bubba-dough

    engine bore

    I've always been the .030 type of guy. A decent set of forged pistons are gonna cost $300 - $350. So you may want to look into a 331 / 347 kit like the CHP entry level Street Fighter kit for under $850? Its all about you budget and goals though :shrug:
  19. bubba-dough

    SuperCharger Tuning Help

    :nice: Assuming you weren't having any problems before the s/c install, and that everything is installed correctly, starting point settings should be like mentioned with the addition of the tps @ ~1V. Plus FMU's are junk band-aids. Get the proper size injectors. If you have a pretty...
  20. bubba-dough

    zex ?

    The unit works by saving the voltage sent out of the tps at full throttle. So something is happening that is making the unit store a voltage that is the same a 3/4 throttle. Basics first. Is the nitrous management unit grounded properly? Are you connected to the correct tps wire? Is the...
Top Bottom
Back
Forums
Menu