Search results

  1. H

    What is it worth

    I have been out for a bit so I am sorry I didn't respond sooner. I can't say that the motor is seized but the lady told me it was. I wish it was the FB or a V8 but sadly it is not or at least the fender was not badged as a V8. not having access to the VIN I can only assume the I6. Did Ford...
  2. H

    What is it worth

    You know you hear of the story of the little old lady that has an old car in her garage to sell and you go in and find a gem? Well I was doing some lawn work with my dad the other day and a little old lady in a wheel chair let me see her gem. She was the original owner to a white, 1966, six...
  3. H

    What's stopping me from using a T5 out of a F150?

    Actually it is a Mazda M5R2 or a M5R1 (depending on F150 or Ranger). The rest holds true. The Shifter is too far forward to use, and is a bit longer to the tail as stated. The ratios are for truck pulling instead of car driving.
  4. H

    Drilling for the Emblems...

    When you buy a repop it is not drilled.
  5. H

    76 maverick spindles on a 69?

    I have yet to put the 66 to the road but the install was just what you would expect to do. I was replacing all the brakelines so I was able to run them as I needed for the Maverick. My advise is make sure you get everything, like the mounting pins and various bolts. makes it easier. The only...
  6. H

    76 maverick spindles on a 69?

    The yard man speaks with wisdom. If the granada will fit then so will the maverick. My 66 is running Maverick spindles right now.
  7. H

    History Check

    Ford can give you build sheet data.
  8. H

    Does anyone know the true diameter of a 157 & 164 tooth flexplate?

    You shouldn't need this but I have a factory matched flexplate and bell for the C-4/early 302 157 tooth. and I know what the correct part number for the starter is for the match. Email me.
  9. H

    66 stang. need pedals for an auto trans.

    I got a clean pedal and mount from a 65 (same as 66). I can trade with you or sell it for low cost. Send me an email. I even got the smaller flexplate scatter shield and bell housing for a C-4 I can throw in......
  10. H

    The Reenmachine DOHC '67 Shelby Clone Convertible Progress

    Did a few telecomm installs for the military. I think the logic on wax is it is faster to do a long bundle, cheaper and will hold up in a fire better than a plastic strap. Once you learn to use it you never want to go back....
  11. H

    Warranty Plate

    Contact FORD for the missing information then call Marti and get your reprint...
  12. H

    The SN65 project car

    Could you open up list permissions on the folder to be able to browse it?
  13. H

    quick question - flywheel

    I thought it was 82 but you have "lived" it so....
  14. H

    MediaBlasting

  15. H

    quick question - flywheel

    What is the tranny? It really depends upon the belhousing/tranny....
  16. H

    I need some help identifying spindles

    If you are trying to put this into a I6 car and it has the original steering stuff, then the tierod ends will be too small. ALL of the steering stuff will need to be swapped out.
  17. H

    Another eBay scam

    You can find this same money scam on ebay everyday by doing a search for kubota and find a listing that is under $8k, no bids and has a "pre-approved bidders" list. Ebay is stupid to allow this as most all of the pre-approved bidders auctions are fake, money scams.... check out...
  18. H

    carburetor help!!!!!!!!!!

    With that head you can run most any 2bbl you want to but if I were to spend $800 for the head and I didn't want to do the contraversial V8swap the I would look at swaping in a 250 and tweaking it up. Not much point in upgrading the head on a tired 200.
  19. H

    5 lug 8.8 conversion problem... need help.

    dumb question here but why are you installing an 8.8 and trying to use 7.5 axles?
  20. H

    Bellhousings

    That means your 302 is pre 1982 or H.O. 302. Post 1982 non H.O. 302s use a different flywheel/Flexplate. :nice: 250 I-6 and 300 I-6 will also share the bellhousing mounting pattern as the Winsor family blocks. :shrug: Correct me if I am wrong but don't scattersheilds vary by the type of...
Top Bottom
Back
Forums
Menu