Search results

  1. pumm3l

    I give up, I cant get that stock H pipe off.

    Are you using a wrench on the top of the bolt while you try to spin that nut off? If you can try to get someone down there with you, one to start turning the wrench and the other to use the ratchet on the nut, that's how I usually break it (although I've gotten pretty good at it and can turn...
  2. pumm3l

    2000 gt ss brake lines

    I got the Russell's no problems for 2 years huge improvement over stock, make sure you get new crush washers. I think my Russell's came with em.
  3. pumm3l

    Black out tail light.

    How is that paint and clear holding up to mother nature?
  4. pumm3l

    pump assembly tubing

    sweet! Thanks for the info. I did some searching and found this: http://www.highperformancestangs.com/forums/showthread.php?t=2578 Looks like this will kill 2 birds with one stone. Thanks again.
  5. pumm3l

    pump assembly tubing

    I bought a cobra tank a few months back from a salvage yard, I was planning on finally putting the new tank on this weekend but I thought I should check out the pumps and make sure the tank was clean before I put it on. As I was pulling out the assembly the tubing on the pumps startled to...
  6. pumm3l

    power steering going?

    Finally got around to fixing this. It was the steering rack.
  7. pumm3l

    6 bolt crankshaft

    damn i was afraid of that..... what's different about the 6 bolt crank that it won't fit in the windsor block?
  8. pumm3l

    6 bolt crankshaft

    Can I use the 6 bolt GT crankshaft in a 99 GT windsor block? The original crank had 8 bolts and thought I saw somewhere that those crankshafts (the 6 bolt) only fit in the romeo blocks, is that true?
  9. pumm3l

    power steering going?

    you can elaborate a little more on this? if I had a leak wouldn't I notice the fluid being low? can you describe the bellow boot i found this image on ebay: which is the bellow boot? Thanks for help.
  10. pumm3l

    power steering going?

    i put the car up on jack stands yesterday and visually inspected and I don't recall noticing anything that would be interfering with the shaft. If it is the steering rack wouldn't I be able to feel it even with the car turned off (no power steering) ? Also while I had it up on jack stands...
  11. pumm3l

    power steering going?

    I did some searching and it seems like when the power steering pump starts to die it starts to make all kinds of groaning noises. My pump is pretty quiet no more noisy than usual but this morning my steering started feeling strange if I leave the steering wheel centered(foward) and try to...
  12. pumm3l

    Vibration around 1400 rpms

    finally fixed that vibration..... Right before I replaced the flywheel, my front brakes needed to be replaced one of the pads scored my rotor and pepboys wouldn't cut the rotor because they said it was under spec. I bought a cheap rotor to hold me over until I did my next brake change which...
  13. pumm3l

    valve tap?

    any idea if I'd have a problem with them checking my engine out since it's not the original motor?
  14. pumm3l

    valve tap?

    okay so I took the car to a mechanic to check it out, he says he's 95% sure it's a sticky lifter or maybe the timing chain (probably unlikely). sooooo after blowing up an engine once, and hurting this one I plan on doing a rebuild so I don't have to worry about wether I have a car this week...
  15. pumm3l

    valve tap?

    just got in from changing the oil.....no metal fragments or silverish looking oil thank god, tomorrow I'm gonna try to pull the valve covers and then go from there.
  16. pumm3l

    valve tap?

    gotcha i'll check it out, I'm gonna change the oil this weekend and pray for no metal bits, after that I'm gonna do as you suggested and see if I can find which side the tap is coming from, then start tearing into it. Once I pull off the valve covers do you guys have any tips on things I should...
  17. pumm3l

    valve tap?

    What's the difference between an automotive stethoscope and a medical one? I have a medical one....
  18. pumm3l

    valve tap?

    took a sound clip of my tapping: http://www.sstang.com/audio/tapping.mp3
  19. pumm3l

    valve tap?

    did your tap go away when the engine warmed up? See I know what a spun bearing sounds like, this this sound is similar but the only difference is that this tap goes away with the engine warmed up and I only hear it at idle. The "death rattle" is something that gets worse over time? I just...
  20. pumm3l

    valve tap?

    not quite sure what you mean...
Top Bottom
Back
Forums
Menu