Search results

  1. pumm3l

    valve tap?

    last year I replaced my engine because of a spun bearing. I've been driving around with this 02 explorer engine for almost a year and took it to get dyno tuned with the nitrous last night, my old motor I was careless and didn't check the oil before getting on the car thats how I blew that engine...
  2. pumm3l

    Oil capacity... two different answers.

    yea i know exactly how you feel!! I have a 2002 explorer 4.6L with my 99 gt pan on it so I'm completely freakin lost! I went to fordparts.com and looked up an oil pan and it says the oil pan is the same from 96-04??? yet we have all these different recommendations. I just changed my oil...
  3. pumm3l

    Defective flywheel

    I bought a flywheel back last year when I did my swap, decided while I had everything apart I might as well change the clutch and flywheel. Funds were limited after having to buy a new engine and all the other misc. parts I needed so I tried cutting corners as best as I could. I found this...
  4. pumm3l

    Vibration around 1400 rpms

    no it's not rpm related, I only get it at 50-55 mph while moving doesn't matter if I'm in gear or in nuetural.
  5. pumm3l

    Vibration around 1400 rpms

    what I did was throw the rear of the car up on jack stands and then I took it up to 55-60 mph and there's NO vibration, so I assume if it were the driveshaft even with it on the jackstands I should of felt the vibrations right? I notice when i'm at that speeds (where it vibrates worse) and if I...
  6. pumm3l

    stang "drained the snake"

    same thing happened to me a few months ago, I took out my fan to have more clearance when I removed my crank pulley when I put the fan back in I forgot to plug it in, about 5 mins of city driving I noticed the car starting to over heat. Did you notice if the fan was going when it was...
  7. pumm3l

    55mph steering vibration

    yea under 55 I have no vibration, as I go faster the vibration starts to smooth out but you can still feel it a little.
  8. pumm3l

    55mph steering vibration

    Tires are about a month old had the alignment done like 2 weeks ago tire pressure set at 29psi wheel bearing (how can I check these?) condition of your bushings (again not sure how to check these) condition of front end components - meaning what? Your shocks and strut - have i have stock...
  9. pumm3l

    Help car wont stay running

    next time it happens get somone to get inside the car and hold their foot on the gas to keep it running while you get something to tap the IAC (you don't have to whale on it) the IAC tends to start sticking after awhile and tapping it can help free it up, this should tell you if it's the IAC or...
  10. pumm3l

    55mph steering vibration

    I recently fixed a vibration in my car that I was getting at around 1400 rpms (bad flywheel) but now I have a new vibration, was probably there all along but I didn't know realize because of the other vibration. Anyway This vibration I get at around 55 mph which is where it's worst, it starts...
  11. pumm3l

    Vibration around 1400 rpms

    sigh....well I have a new vibration heh, the vibration at a particular rpms is gone but now I have a new vibration I started to notice this one recently though this vibration happens around 50-55mph doesn't seem to have to do anything with any particular rpms 50-55 is about 1500-2k rpms I think...
  12. pumm3l

    Vibration around 1400 rpms

    really? I didn't have any problem with it at all, the center came out with 2 big hits, and the outer part came out in 3 hits, didn't really take any effort at all, could of been that it's only like 6 mos old tho.
  13. pumm3l

    Vibration around 1400 rpms

    some pics Here's some pics from last night: old flywheel and old clutch: new flywheel and new clutch: slide hammer and pilot bearing remover: I did send an email to the company I purcahsed the defective flywheel to but I bought it last nov. so I doubt it'll do any good, just curious...
  14. pumm3l

    Vibration around 1400 rpms

    okay I found it, i plugged the cig lighter & abs switch back in but forgot to plug the main harness that's right there, everythings is good now.
  15. pumm3l

    Vibration around 1400 rpms

    ahh I saw 2 connectors on the tranny that I had to disconnect when we pulled it I assumed one of them had something to do with the traction control. I did unplug the switch when I removed the shifter but I know I also plugged it back in, I guess I'll have to fiddle around with it find out...
  16. pumm3l

    Vibration around 1400 rpms

    Vibration gone!! thank god! got to work on it about 9am this morning and finished up about an hour ago, everything is great, except now I can't turn my traction control off, I must of not hooked seomething back up the light on the console doesn't even light, so anyone know which wires are used...
  17. pumm3l

    Vibration around 1400 rpms

    Finally got all the parts yesterday, I'll be doing everything sunday.
  18. pumm3l

    Vibration around 1400 rpms

    Centerforce is a good brand generally expensive brand but none the less good quality. I hope that's not true and this was just a fluke about the defective parts.
  19. pumm3l

    Vibration around 1400 rpms

    yea what I had before was an excedy ebay flywheel kinda like this but the one I got was a 6 bolt and could accept an 10.5" or 11" clutch and I was using the king cobra clutch with it. I can't go with a stock flywheel though because I'm using a 2002 romeo block with a t45 trans so I need a 6...
  20. pumm3l

    Vibration around 1400 rpms

    so here's the update: pulled the transmission off, first off how the F are you supposed to get the alignment dowels in the flywheel? I had to like almost hammer it in and it barley even seated itself but upon hammering it in I decided to check out the pressure plate and noticed that the...
Top Bottom
Back
Forums
Menu