Search results

  1. M

    2 Codes - P0340 - P1401

    sweet, thanks........
  2. M

    2 Codes - P0340 - P1401

    After some googling I think I know what the DPFE sensor is. It mounts at the back of the intake and has two hoses running to the EGR tube.....?
  3. M

    2 Codes - P0340 - P1401

    If the cam sensor is plugged in and the wiring seems to be in good shape should I get a new one? Where would I find the DPFE sensor? Thanks
  4. M

    2 Codes - P0340 - P1401

    I don't trust the dimwits at autozone and thats why I came here w/ the codes. I'll check the CAMSHAFT sensor tomorrow. The car runs great except for the timing. Its acting like it needs adavanced a few degrees. The only motor mods on the car are CAI, 75mm TB/plenum, headers, catted x...
  5. M

    ABS light

    would this code be read along with the CEL cause I just had that done? :shrug:
  6. M

    Help me decide (gears and tune)

    I would go with the tuner so you can upgrade. There's also many more benefits that come w/ the tuner such as data logging and reading your CEL.
  7. M

    ABS light

    My ABS light comes on every once and awhile when driving. Sometimes its on when I start the car, sometimes it comes on while driving and will shut off before I get to where I'm going, etc. etc. There is plenty of fluid and I dont know what else to do. The car was sitting for 2 years and I...
  8. M

    2 Codes - P0340 - P1401

    This car has been sitting for 2 years and I finally got her all put back together. The new block has 300 mi. on it. There are 2 codes being thrown... 1. P0340 - Crankshaft position sensor Im getting a new one from Ford tomorrow and hopefully it will clear that code. Any additional input...
  9. M

    Vibration getting bad under car???

    My first guess would have been the u-joints.....How did you inpect them? Just by rotating the driveshaft and looking for play? Even if everything seems tight those bearings could be wearing out.
  10. M

    Advice on a clutch

    Im totally satisfied w/ my KC clutch. Some people complain about the stiffness but I love mine.
  11. M

    how to remove gum from paint?

    +1 for peanutbutter I have also heard Mayo works as well
  12. M

    Mac 80mm CAI questions - 2000 GT

    The factory mass air sensor should fit fine. A tune could release a few extra ponies but by no means would you NEED a tune. I have the MAC fenderwell CAI and it DID NOT fit very well at all. :nonono: I couldnt even use the plate that seperates the engine bay from the fenderwell. The piping...
  13. M

    Resetting my ECU??

    great....thats NOT what I wanted to hear. Ill have them printed out and post them here.
  14. M

    computer reset

    I had posted a similar thread and thought I might find the answer here. I have a new bottom end w/ stock heads and CAI, TB/plenum, headers, catted x, and CB. I was wondering how to reset the PCM to learn this new setup and if it was even neccesary. Right now it runs great but needs the...
  15. M

    Resetting my ECU??

    Everything is solid..no loose ends anywhere. For example, its throwing codes for all 4 O2 sensors when all 4 of them are brand new and installed myself. I did the complete rebuild myself and personally re-connected the wiring harness and all vaccum lines etc...
  16. M

    Fluid Change

    ^^^That sounds like a good reason. Another tip..... When filling the rear end have a jack underneath the passenger side of the axle so its angled with that side higher than the drivers side. This will allow you to get more fluid in there.
  17. M

    Resetting my ECU??

    I have recently put a new block in my car along with some other simple mods.. CAI, 75mm TB/plenum, headers, catted x, cb...those are really the only power mods. Other than the timing needing advanced the car is running strong. I have all kinds of codes thrown and need to reset the ECU or...
  18. M

    Fluid Change

    BMW or Goldwing?
  19. M

    Fluid Change

    If your changing the diff. oil, dont forget to add the friction modifier. Im not sure if it is required with the use of RP but its recommended when using the motorcraft equivelent. I believe it comes in a 4 oz. bottle and you can get it over the counter at a ford dealer. 1 bottle per change...
  20. M

    Tools needed for X pipe/catback install? Tips?

    Put your jackstands underneath the 2 body rails that run down either side of the car. You cant miss them. You dont want to support the car from the rear axle because you want the rear end to sit as low as possible to make the removal of the exhaust easier. You will want all the room you can...
Top Bottom
Back
Forums
Menu