Search results

  1. R

    TwEECer and Ford MAF sensors

    Will a Tweecer tune for any size injectors/maf as long as you stick with a ford MAF sensor? Also would an 80mm MAF be a restriction in a boosted car? Would it be worth it to go with a 90mm?
  2. R

    My DIY turbo kit is underway...PICS!!!...AGAIN!!!

    Thanks a lot for the all the answers you cleared up a lot for me glad to have members llike you on here that liked to have there brains picked:nice: , what I asked was what I was most concerned about because as far as the hotside plumbing and intercooler piping which doesnt seem like much from...
  3. R

    My DIY turbo kit is underway...PICS!!!...AGAIN!!!

    Did you get the turbo's from a manual turbocoupe or auto? Do they come with the correct wastegates to build at least 6-8PSI or do I need to buy something else for them? Also which one do you have because I see one is watercooled and the other is oil fed: FORD T-Bird 85-86 2.3L (auto) GAR...
  4. R

    My DIY turbo kit is underway...PICS!!!...AGAIN!!!

    What pipes did you run on the inlet side of the turbo? Looks like you have two vaccum lines connecting the turbos and runnig down the center of the motor? What are those for and couldnt you have put two filter right on the inlets? Or are those bolted pipes required to run those t60 turbos? Im...
  5. R

    pics of relocated battery

    Ok I completely understand the ground and 18gauge wire runnin from the alternater to the switch and back to the alternator. Only thing I am not understanding is the whole power side im just lost or having a brain cramp, as far as I can understand you run the positive from the alternator back...
  6. R

    pics of relocated battery

    Sorry to bring up such a old thread but where does the positive from the switch go to upfront? Does it go to the alternator or to the starter? And does the alt power go back to the battery?
  7. R

    Best location for a wideband O2

    Definitly makes sense to go the easier route with wiring/position of the O2 if the lean/rich difference between each bank is minimal.
  8. R

    What other cars have a Fox 4-lug pattern?

    4x4.5? I know there all 4x108mm up till 93, which converts to 4x4.25, I know for sure a Mercury cougar/thunderbird 80-88 has the same size cause I owned one and bought custom drilled wheels for it in the past, also the same years escort as well but wouldnt match up right in the rear due to it...
  9. R

    My DIY turbo kit is underway...PICS!!!...AGAIN!!!

    Did you end up going with a custom/self-made downpipe back exhaust system or did you mate it to h-pipe/xpipe setup? Im curious as to how loud a setup like that would to run custom side exit pipin from the downpipe with no cats...:hail2:
  10. R

    Best location for a wideband O2

    What would be the place to put in a wideband O2 to get the most accurate reading on a h-pipe/x-pipe system for a stang? Or is there one that usually runs leaner? I am coming from a FWD V6 2 to 1 y-pipe setup which was a no brainer, I just dont like the idea that the wideband would only be on...
  11. R

    running a 50% crank underdrive pulley...charging problems?

    Oh alright if the difference is that little I wont even bother then, thanks for the advice guys.
  12. R

    running a 50% crank underdrive pulley...charging problems?

    bump....
  13. R

    Will a Crane HI-6S CD ignition work with a fox?

    Will it hook up without any wire tapping? Is it a good system to eventually run N20 and use its yellow wire with a 12V source to run the lower rev limit for launches?
  14. R

    running a 50% crank underdrive pulley...charging problems?

    Now that I basically got my belt routing situation figured out and decided to go with a electric fan/water pump with DC controller, and a/c delete with p/s bracket to move it up, I had a question about running a race 50% on a street/weekend car that will have an electric fan/water pump. I...
  15. R

    Torque boxes

    Where do the 2plates with only 2holes go? And the single large bolt closest to the ground is that already in the torque box or has to be drilled through?
  16. R

    Tensioner question running electric fan/water pump with no A/C

    When the car gets out of the body shop I plan on doing a pretty decent engine bay face lift, i've already found the right Moroso electric water pump, have a left over fan from my old SHO project, soon to order DC controller, 3G will get from local parts store along with wiring/fuses etc., and I...
  17. R

    Torque boxes

    Would having a metal worker fab something similiar to what is in the pics work just as well? How thick is are the plates that in the interior side? Are those factory bolts/nuts that are in the pics going into the body, if not should regular bolts be used or grade 8+?
  18. R

    Has anyone bought a turbo kit from this company for their 5.0?

    Looks like a nice kit I like how it isnt as visible as the other turbo kits out there, only problem I see for the fox kit is, wouldnt you have to cut that tubing to get a MAF sensor fitted on there?
  19. R

    what do plugged catalytic converters act like??

    Dont know if my experience is too relavent to this problem, but years ago when I modding my first high miles motor(150K+) in my manual 93 Taurus SHO I had the same exact problems your having, it eventually got worse and worse till it wouldnt even start with a push start, I went over the whole...
  20. R

    mexicano block!!

    How much is a kit to make non roller blocks work our hyd rollers? Or link style lifters kit?
Top Bottom
Back
Forums
Menu