Search results

  1. Labora

    SN95 Drive Shaft Length?

    How far into the tailshaft does the yoke need to be? I have about 3.3 inches inside with the car having weight on the rear suspension at a slight rake. (Front Higher) This is in my 94 with a 351/AOD, I was previously using this drive shaft with a 302/T5 it is a FMS aluminum one so I was wanting...
  2. Labora

    95 Cobra Carpet

    Somewhat apart but maybe help you decide.... http://i36.tinypic.com/2s1m1qt.jpg http://i35.tinypic.com/34q76zm.jpg http://i33.tinypic.com/287zst0.jpg
  3. Labora

    Sn95 Fuel Hose Fires

    Heard about it, never seen it happen to any sn95s I've worked on personally. I do plan to replace my stock under the hood lines but that is only because I am going to aftermarket fuel rails. Deferentially something to keep a eye on and inspect regularly.
  4. Labora

    Distributorless Ignition System thoughts

    Good info here, posting to bookmark for later. Going to COP is tempting since I will be going to Megasquirt.
  5. Labora

    Aod Vs T5 Crossmember?

    Thanks Chythar, always helping me out on here. :D
  6. Labora

    Starter Removal PITA

    As mentioned longer extension the better, think that is bad try the 3 bolt starter some of the 4.6s had!
  7. Labora

    Help With 94 Cobra Mods

    You are all over the place brother. First of all if you plan to build up a engine get a solid plan beforehand, adding aftermarket heads a (presumably) stock intake and a letter cam will not get you a decent combo what so ever. If all the components do not match flow wise you will be leaving HP...
  8. Labora

    Aod Vs T5 Crossmember?

    Is there a difference between the two? I am going from T5 to a built up aod and wondering if I should track down a different cross member or not. Do foxbody crossmembers interchange with 94-95 stuff or is it diffrent?
  9. Labora

    Build Thread "Rising from Ashes" 94 Cobra build thread

    OMG that is so sad. The blue one was was just too clean, to the point I don't think I could bear to drive it down the street. Sorry for your loss. I'm actually about to have my home owners policy changed to another carrier, going to make sure they cover my project cars! Good luck with the new...
  10. Labora

    Build Thread Project Phoenix (94 Cobra) Part 2

    Thought I would post a update as a new round of upgrades are about to start. In case some people don't remember me/my car check out my original build up of the car. http://www.stangnet.com/mustang-forums/threads/project-phoenix-94-cobra.766511/ Anyhow I drove the car for awhile was daily...
  11. Labora

    Been A Long Time!

    Wow few old names in here. :) So you going to go solid roller? :D And not bad ET really for having not driven the thing in forever.
  12. Labora

    Build Thread Jamee's Build Up Thread

    I just had a similar fuel clip headache. Best two options are go to parts store and have them open a book and order you what you need. I know most parts stores don't realize that they can get stuff outside of the computer! Or check this site. Ron Morris Performance: Stock Ford EFI Fuel...
  13. Labora

    Bone stock w/tfs stage 1 cam?

    IMO the cam is the weakest link of a stock 95 Cobra H/C/I. If you have things apart I highly recommend at the very least a light port job on the lower intake and a cam with upgraded springs. The car will run fine on a stock ECU, at the worst you may experience some stalling at idle from time to...
  14. Labora

    Project Phoenix (94 Cobra)

    Figured I'd post a update since I'm planning some more work soon. Few pics....:D I'm sure someone will ask the track times I've been able to cut, and nothing really special. Just a 8.9 with a 2.1 60ft at around 83 MPH. For those who don't speak 1/8th around a high 13, have to forgive me...
  15. Labora

    Will These Look Good?

    Haven't seen them on a sn95 that I can recall. More then likely because the offset is very different.
  16. Labora

    Car burning oil? (Thinking of replacing valve seals)

    I've probably put around 2000~ miles on my car since I got it running and have noticed it is burning a decent amount of oil. The story with the engine is I had it in my 95 and moved it to this 94 it is around 90k miles (stock longblock) and never burned any oil in my 95. When I had the motor...
  17. Labora

    Is short belt routing different on a Cobra

    Yes it is different because the 2 lines you are hitting are the oil cooler lines. (Which are only on Cobras.) What I did was delete the oil cooler, install a fl1a filter (same as what GT uses) and ran the same belt route a GT would.
  18. Labora

    Project Phoenix (94 Cobra)

    I have them sitting out at the shop ready to go with a 1" spacer and all, they came out awesome black/silver. But the more I think about it rather than having a intake spacer on there I'd rather just have a Nitrous plate. :D So I'm keeping my eye out for a deal on one and trying to hold off on...
  19. Labora

    buying gears

    I would. 25$ is not a huge amount and the labor to have a them installed is typically more then the gears. (So if you by a crappy set of worn gears guess what your paying labor again to fix the issue.)
  20. Labora

    Wiring Help! Windshield Wiper Related

    Having this exact issue. Also tried changing the mutli switch out with a spare and no change. Checked/changed the "wiper" (30amp) fuse no change. The wipers and windshield sprayer are not working. Usually I would open my ford book and take a look at the wiring diagram, but a friend is borrowing...
Top Bottom
Back
Forums
Menu