Search results

  1. 4dStang

    Cost of subframes-Cost to install

    I'll just log in as another. Why not! I try to help and Dagger gets his word out
  2. 4dStang

    Cost of subframes-Cost to install

    I know. It is daggers stupid fault for being an azz.
  3. 4dStang

    Cost of subframes-Cost to install

    ... DUH!! it is all labor dude. I am not buying /selling anything. I am offering free assistance. So why don' you think about that again!!!!!!!!!!!!!!!!!!!! I just like to weld. So hang out at mienakkee since you can't weld. I CAN WELD!!!!!! I actually like to help other stangers.
  4. 4dStang

    Cost of subframes-Cost to install

    Who has added aftermarket subframes? Cost of frames? And how much for installation? I wanna know because I built mine for $6 worth of steel and my own welder. I just want to see how much people have to pay for such a simple add-on. If anyone wants CHEAP subframes, PM me and I...
  5. 4dStang

    replacing quad shocks with solid bar?

    My mom is a fabricator (quilts) Any body can fabricte. Get references before getting you stang fugged bad. Use tested aftermarket and ask alot of question.
  6. 4dStang

    Burned cobra mustang, brake questions

    94 95 rotors will not work on a Fox. The offset is different. (IMO) Expensive, go to Baer four or six piston More expensive, go to aeromotive Cheapest, SVO larger pistons Forget the slotted or drilled rotors. The fancy rotors are just hype, but I am sure to be corrected, guaranteed...
  7. 4dStang

    replacing quad shocks with solid bar?

    I think that the steel would tear the connectors. I have upper/lower CA's and removed my quad's. I would like to add a panhard bar to my four link but I have no problem so far after adding subframes and re-enforced Torque boxes. Chris
  8. 4dStang

    ignition box mounting

    From what I have seen in the past, many remote install the battery to the back and use the baterry box up front for the spark box. I tried to find a spot years ago and just could not a spot to put my 6AL under the hood. Maybe others may have different results. Chris
  9. 4dStang

    alright...either im an idiot or the car is possesed. help me solve my tach mystery

    Good point!
  10. 4dStang

    alright...either im an idiot or the car is possesed. help me solve my tach mystery

    I had a 95 cobra with afunky intermittent tach. Turned out to be the tach itself after replacing it with amonster autometer. Electronics go bad sometimes and replacing the tach will basically swaping the gauge panel with a repaired or used unit. Just my experience. Try a different tack for...
  11. 4dStang

    Installing fuel pump, Anything else I should replace while I am in there? thanx

    Sorry, It has been a while since I bought a set. I did not know they went up that much.
  12. 4dStang

    rear main seal removal tips please

    On my 93, I just used a pick (not picture) to lift it out using five or so area's. The seal simply goes in with a rubber mallet. Super simple. CB
  13. 4dStang

    Installing fuel pump, Anything else I should replace while I am in there? thanx

    :eek: $20 bucks for a rubber grommet. I paid $5 ea. at the dealer for two. You HAVE to change the grommet or the tank WILL leak. Every tank I have taken apart needed a new grommet. They tend to stretch from the gas. Make sure you clean the surface where the grommet goes, wire brush...
  14. 4dStang

    Mystery noise, suspension, driveshaft, tranny mount?

    Subframes connectors have nothing to do with the torque boxes. The tear is from the axle twist usually on the passenger side. The boxes are just sheet metal. You may find some re-enforcemets at 50resto.com or even on crapbay (ebay). Stick your head under the car where the lower control arm...
  15. 4dStang

    Your O ***** moments

    Tired. It was 4am.
  16. 4dStang

    Your O ***** moments

    Once I was in high school in SLC way back in 1988. I was riding in the back of an old Jeep style Land Cruiser. We dropped my friend off and I jumped in the front seat. Before I could belt up, my budy flipped a U-turn. No doors, guess where I went. I was laying in the middle of the road at...
  17. 4dStang

    Mystery noise, suspension, driveshaft, tranny mount?

    Your torque boxes are ripping. I just welded my cracks up because I had the exact same problem. There are torque box reenforcements available for under $100. I just used some scrap angle iron and my MIG to weld it up. I found my crack when installing subframes. See pic for the torque box...
  18. 4dStang

    Death Metal on Discovery

    I have been into metal since it began. There has always been the PMRC in music censorship. They only make more noise so more metal heads stand up for their music. As for the gun issue, my last job thought that because I listened to Slayer and many others and have a few tatoo's, that some how...
  19. 4dStang

    HELP!!! Need to borrow a part from someone in STL, MO area

    I am in desperate need for a block spacer plate for a 87-95 Mustang 5.0 with a T-5. I am unable to get the part until Wed or Thursday, but if someone in the St Louis area has the part new or used, and will let me buy or borrow the part, I will give you a new one this week or pay you for it...
  20. 4dStang

    Took the Stang into the shop today.

    How high are your hydro carbons? The o2 sensors could be richening up the engine. You don't seem to have too many smog related modifications in your sig. Some how you are obviously runing rich. A good way to cheat the smog on a odb1 car is to loosen the exhaust ever so slightly to get a...
Top Bottom
Back
Forums
Menu