Search results

  1. fin1

    Where to get a ati procharger in PGH???

    I had mine purchased and installed by ASAP in Allison Park. They did an excellent job with my installation/tune. http://www.asapbyed.com
  2. fin1

    HC Trap Final Answer

    There is no final answer because it's not that simple. Yes you can remove it w/o a tune and you car should be fine. But I would recommend you leave it in and then remove it later as part of a CAI install (for example). Then you can get a tune with it removed in conjunction with the CAI. IMO, the...
  3. fin1

    4.10's ?

    Yes they can and no, a tune is not needed.
  4. fin1

    Which CAI do you use?

    I had the Steeda and was very happy with the results coupled with a good tune.
  5. fin1

    4.10's ?

    No regrets and gas mileage has not noticeably changed. 1st gear does go by fast now but I expected that much. 2nd pulls like a rocket.
  6. fin1

    200 RWHP Bolt On

    The shop I used didn't use the Diablo tune. It was a custome dyno tune using the Diablo tune & the SCT tune as a reference. The Diablo tune was very rich. My final A/F was 11.7:1. The shop I used understood my concern over the impact of this much boost on a new car so they were conservative...
  7. fin1

    New blower

    That's well over what ATI even quotes. That's damn nice but how are you getting that much rwhp? Are you using a 10 psi pulley? What rmp did you peak at? Your sig states you got an ET: 12.902. Is that with the blower? Thanks.
  8. fin1

    New blower

    No it doesn't since the ATI comes with a 3-core intercooler.
  9. fin1

    New blower

    Last one...
  10. fin1

    New blower

    two more...
  11. fin1

    New blower

    I just got her back.
  12. fin1

    2005 Mustang GT fuel pumps...how much HP can they handle?

    Good read. http://www.modulardepot.com/?show=articlesdet&aid=55
  13. fin1

    Strut tower brace

    I have the xcal. I have been very happy with the Steeda products.
  14. fin1

    Strut tower brace

    I have the Steeda. Not sure how it compares to the Ford one though.
  15. fin1

    Help w/ pillar gauges

    Ya me too. I have the blower being installed in a few weeks and I'll have the shop wire the gauges then too.
  16. fin1

    Help w/ pillar gauges

    Does anyone have any idea which wires to tap into for the dash lights. I've installed 3 AutoMeter Cobalt pillar gauges and they have back lighting that runs off the dash lights. I'm having a hard time find the one to tap. Any help would be appreciated.
  17. fin1

    Hmmm...

    I think it's important to understand your rights as well as how your mods may affect your car & the warranty you have. Give this a read about the Magnuson-Moss Act: http://www.dummies.com/WileyCDA/DummiesArticle/id-2669.html For example, I plan on adding a blower in the next few weeks. I...
  18. fin1

    Any interest in RPM/MPH Gear Ratio Charts??

    or you could use this: http://www.f-body.org/gears/
  19. fin1

    525+ HP is on the way for me!

    Blkgt05, Orded one too. Installing it the week of May 9th. The shop wants her for the whole week to install, test and tune.
  20. fin1

    Anyone Fanatical About Their Car?

    I'm the same way. Mine is a daily driver so it is subject to the daily road and weather abuse. I wash it wash & detail it once a week but don't touch it during the weekday. I would probably go insane worrying about it otherwise. ;)
Top Bottom
Back
Forums
Menu