Search results

  1. dodgestang

    Wheel hop

    Most t5 mounts I have seen lower the tail shaft of the tranny to install it. Did you confirm/check your pinion angle when you completed the installation?
  2. dodgestang

    How do I change gas tank sending unit?

    Naw overly complicated IMO. Drive the car till its almost empty, put the car up on 4 jack stands with the nose just a little lower than the rear, disconnect the fuel line and point it into a 5 gallon gas can to drain the tank then go inside and watch TV to warm up for an hour. Come back out...
  3. dodgestang

    Competition Engineering traction Bars CEE-2109

    Slot the mount plates for the smaller u bolts.
  4. dodgestang

    How do I change gas tank sending unit?

    Climb under the car and take a gas bath, good for getting that pesky dirt behind your ears off. It comes out the back side of the tank from underneath.
  5. dodgestang

    65 Fastback complete motor and trans 4 sale 312 Ci

    Usually helps to know where you are located.
  6. dodgestang

    351C in a 67 Mustang Question

    If I didn't have to touch the towers in my 65....you certainly wouldn't need to in a 67.
  7. dodgestang

    351C in a 67 Mustang Question

    It will fit, it bolts in using the same motor mounts since it is the same bell housing as the one you are taking out. You can bolt it right up to the existing auto in the car or invest more in doing the stick conversion.
  8. dodgestang

    Aod cross member and looking for v8 rearend

    Where are you located? I have something for you rear end issue, but shipping a rear housing, a pumpkin, and axles is expensive.
  9. dodgestang

    '65 Dash pad

    Got the email, I'm going to pass for now.
  10. dodgestang

    '65 Dash pad

    I'll take a photo please. nick at dodgestang dot com
  11. dodgestang

    68 shelby hood for a 65 66 ?

    My bad....so hard to keep it all straight sometimes ;)
  12. dodgestang

    68 shelby hood for a 65 66 ?

  13. dodgestang

    lowered 64-66's?

    The certainly seems like an open ended question. I installed lowering springs.
  14. dodgestang

    new 408 low dyno numbers

    That's a small cam ;) Need a larger gap on the plugs. I have 'rumors' that edlebrock carbs are very reliable but never been a favorite when wanting to make some big power numbers. Is it a VS or DP? Stick or auto? What was the RPMs you where seeing the numbers at? What size is the fuel line...
  15. dodgestang

    Lowered 69's? Anyone have good pics?

    There's a couple here....its a little thin...but hey...its a work in progress Dodgestang Photo Archives
  16. dodgestang

    Seat tracks

    I would only do the ones you have to. Putting a reg bolt in there fixes it, but with the threads all the way out the end it makes it a bugger to get started when you need to put the nuts on ;)
  17. dodgestang

    Seat tracks

    I doubt he cut them. More than likey he snapped it off installing the seat. I have done this. I usually just hammer out the old one and then put in a grade 5 or better stainless with a littlle tack to keep it from spinning in the track when I torque.
  18. dodgestang

    '66 w/bullitts+spacers+global west arms= no no

    Do you have the turn stops installed? (aka what struts are on the car)
  19. dodgestang

    351 victor jr under 66 shelby hood?

    Well....according to his profile he does have a 302 :nice: Now you on the other hand...you sure that isn't a cleveland :D At least now there is a definitive answer...if you are handy you can make it work, but it looks like slim chances for an off the shelf bolt and go assembly :mad:
  20. dodgestang

    351 victor jr under 66 shelby hood?

    Yeah, but you have a 302.
Top Bottom
Back
Forums
Menu