Search results

  1. bigbird04

    Fuel Vortech v2 install. need fuel pump help BADLY

    The pump will be kinda hard to pull up . You can pry gently with a screwdriver it will feel like a vacuum is being pulled on it. # 1 goes to your charcoal canister correct ? Try pulling the white clip completely out of the connector with some needle nose .
  2. bigbird04

    Fuel Vortech v2 install. need fuel pump help BADLY

    The filler neck will be hit or miss as long as you unbolt it from the car and are gentle when dropping the tank . I didn't have to replace mine just drop it slowly and change pumps under the car ( don't pull tank from under car drop it enough to do the job no more ) the filler neck bolts to the...
  3. bigbird04

    Fuel Vortech v2 install. need fuel pump help BADLY

    # 1 use your thumb on the opposite side you took the pic From push in on it there, push the line foward then pull it off the clip may be stuck could be hard. # 2,3,4, and ,5 shouldn't have to come off. #6 you need a quick connect tool, which is the only one connected to the pump , and the only...
  4. bigbird04

    Quick question for Night Shifter

    Same problem I have sucks huh ?
  5. bigbird04

    Help understanding relationship between flywheel and engine vibration

    What about driveline alinement since the engines are internally balanced. Could be a loose/ broken motor/ tranny mount , or whole driveline in bind due to mis allignment ? Pilot bearing ?
  6. bigbird04

    Headers

    Thanks mustangman I put off buying these for a long time cause everyone said they sucked on mustangs. In my case they fit , like u said good thick flanges and a LT ceramic set up for around 500 , had to try, glad I did. They may have had fitment issues early on ( pacesetter ) but it seems to be...
  7. bigbird04

    Headers

    Sorry in op i meant to say questions instead of suggestions.
  8. bigbird04

    Headers

    I've had them on my car since August . No fittment issues. Install was time consuming but fairly easy. They actually tuck under my car better than my bbk X pipe did. All and all for the money plus being ceramic coated, which was important to me. I'm pretty satisfied . I just wanted to share my...
  9. bigbird04

    Headers

    Bought these http://www.latemodelrestoration.com/item/PAC-72C3230/1996-04-46L-Mustang-Gt-2V-Pacesetter-Long-Tube-Headers comments, suggestions ?
  10. bigbird04

    '00 Gt Problems

    The inertia switch is in the trunk on the driver side behind the tail light. The car really shouldn't start at all if it is tripped. I was trying to think of simple things to check first. When my fuel pump went out it went out all at once. It died and wouldn't come back. Have you checked all of...
  11. bigbird04

    '00 Gt Problems

    What year model is the car? Your computer will try to compensate for a vacuum leak. You could try and disconnect the battery cable and let it set for about 10 mins. Then start the car and see if it helps. Usually unmetered air will cause a lean code yet your throwing rich codes. Have you checked...
  12. bigbird04

    '00 Gt Problems

    Fuel filter ?
  13. bigbird04

    Question About Deep Dish Replicas

    On my 18x10s the dish from spoke to bead is right at 2 inches maybe some one with some 17s can measure theirs. I would think that if the offset on the wheels are the same that the1/2 in. Would be made up some where else.
  14. bigbird04

    Blowing Smoke!!

    A tune might help, you could be running a little rich after removing your cats.
  15. bigbird04

    4.10 Install Help

    I see a lot of looks but no replies. I don't know how far you are willing to travel for a gear install, but I know a guy that does gear installs fairly reasonably around the Decatur Al. Area. PM me and I can get you his number if interested.
  16. bigbird04

    Testing Sig

    Just testing signature
  17. bigbird04

    What If

    Macs do not have to be removed is my understanding. Not sure about pacesetters. ( I've had them on ls1s, (fit great, buy the way I've also heard horror stories on gts). I just want my LTs to fit right the first time with little or no mods to k member, floor pans, or stearingshaft.
  18. bigbird04

    What If

    Thanks I was thinking I would be better off with out for now. I want macs but the ceramic pacesetters are very tempting. I am thinking of giving them a try.
  19. bigbird04

    What If

    Thanks guys, I could do the labor myself . I did my own gear install ( I'm a mechanic by trade ) Basically the only thing on a car I would be scared to get into would be an automatic tranny. I was thinking the long tubes would be more of a supporting mod for a vortech kit down the road...
  20. bigbird04

    New To Mustangs With A Radio Problem

    There is probably another fuse that powers the amp. Go vols.
Top Bottom
Back
Forums
Menu