Search results

  1. gregpro50

    am i the only one?

    I like both.
  2. gregpro50

    Check it out!! '80 PPG Pace car found!!

    Needs alot of work but I was never even sure that one really existed. Its an exciting find. (link to pics on second page of thread) http://www.foureyedpride.com/phpBB2/viewtopic.php?t=29093&highlight=
  3. gregpro50

    Did I get screwed? (tie rods)

    Confront the shop about it. If they were supposed to replace the pair and they only replaced the one then they should replace the other. Also make sure they re-align it.
  4. gregpro50

    Got my new motorcycle!! PICS!!

    Nice. Here is a pic of my Interceptor.
  5. gregpro50

    Interested in a toyota!!

    I just bought a new Toyota RAV4 V6 for the wife. This is the first year they are available with the 269hp V6. I have to say that thing is sick fast for a little SUV.
  6. gregpro50

    Pics of my '90 GT Vert

    Hey thanks for the offer. Actually my rear seat is in pretty good shape. It is the front ones that are pretty rough. I checked out your car too and yours is really nice.
  7. gregpro50

    Pics of my '90 GT Vert

    Only one I have right now. The white leather seats need to be recovered. Engine pic. Nothing much performance-wise but now it is a driver that doesnt leak oil.
  8. gregpro50

    Pics of my '90 GT Vert

    Here is the V8 pace car. This is the 4cyl turbo with 36k miles. This is the '85 SVO And the '92 GT '82 GT
  9. gregpro50

    Pics of my '90 GT Vert

    Havent been on here a while but I finally got my vert on the road so I thought I would post some pics. Over the winter I did an AOD to T5 conversion. I also pulled the motor and put new gaskets on it and repainted it. I also put an offroad H-pipe with flowmaster exhaust. It just got back...
  10. gregpro50

    man i have been having problems with my 1983 mustang

    Sounds like it could be the timing.
  11. gregpro50

    Looking for member: v8only

    he is over on foureyedpride alot.
  12. gregpro50

    Need help w/ Belt Tensioner

    No. With the belt off just bolt the tensioner into place. It will only go on one way because there is a stud in the back of it that fits into the accessory bracket bolted to the engine. Then put a wrench on the pully bolt and pull it back until you can put the belt on. The tension is pre-set...
  13. gregpro50

    Need help w/ Belt Tensioner

    Just get a wrench on the bolt on the tensioner pulley. The leverage from the wrench makes it a piece of cake. I had to use an 83.5 when I bypassed the smog pump but different manufacturers sizes run different.
  14. gregpro50

    How would I fix this problem?

    The bondo cracked and cracked the paint with it. It must have a pretty thick layer of it. Your best bet is to replace the quarter with a new skin. I have seen some places selling aftermarket ones but I have not had any personal experience with them. If you just repainted the cracks would...
  15. gregpro50

    sunroof delete question

    No just welding sheet metal over the hole will not work if you want it to look halfway decent. The roof is not flat and there would be lots of bondo work involved which you dont want on the roof because it would crack over time. Its your car and you can try it if you want but I am pretty...
  16. gregpro50

    sunroof delete question

    OK I have experience in this. I am changing the sunroof skin on my pace car to replace a rusted one. Basically the right way and the only way to do this is to take off the roof skin and replace it with a solid skin. The hatch and the windows have to come out and then you will need to drill...
  17. gregpro50

    Quick question: AOD to T5 swap

    You shouldnt have to cut any wires at all. It is basically a straight-forward swap. I just did it in my '90 GT vert. You dont need to change computers. The aod one will work just fine. Also the neutral safety wire doesnt need to be cut. I think you may have gotten some bad info.
  18. gregpro50

    No one will install my SFCs or H pipe in Columbus

    Take your car to a local welding shop for the subframes. They will charge next to nothing for it and they wont care if you have cats or are just running open headers... The worst part of and H-pipe install IMO is getting the friggin O2 sensors out of the old pipe.
  19. gregpro50

    thermactor plugs for e7 heads

    Go to your local engine builder/machine shop. They have piles of these things laying around. They usually just give them to me if I bring him a cup of coffee...
  20. gregpro50

    Leaking water

    Are you sure its actually leaking between the timing cover and the block?? I have never had that happen. Could you have had the water pump gasket slip when you installed the new pump or the T-stat gasket slip?? I have had that happen.
Top Bottom
Back
Forums
Menu