Search results

  1. modulistic

    Looking For Help On Surging Idle. Went Through Check List, But Still Surging.

    codes 94 and 44. This is going to sound dumb, but its something to check. I have long tubes on a lowered 5.0 and I hit the rails on a railroad crossing pretty hard. jarred my midpipe and created leaks at the header/midpipe section. car started running like :poo:. the 02 sensors are in bungs...
  2. modulistic

    4.6 Swap Underway. Need Ideas To Solve Rear Axle Problem.

    yeah, the fox donated all the harnesses and much of the interior/steering column to a 4 cylinder, so I have little choice. from my research its going to be about 8 hrs of test fitting and trimming. The upside is that there will be no splicing/wiring diagram head scratching to do.
  3. modulistic

    4.6 Swap Underway. Need Ideas To Solve Rear Axle Problem.

    4.6 is in. not sure if/why I have to swap to the fox control arms. need to do more research on that. still plenty of crap to do. had to grind on the rear tab of the kframe, but otherwise went right in. hood even closes without modification.
  4. modulistic

    4.6 Swap Underway. Need Ideas To Solve Rear Axle Problem.

    Gotta chop the firewall a lot to get the an 95 firewall plate on there. Getting those steering column plates off was a legit 4 hrs of work.
  5. modulistic

    4.6 Swap Underway. Need Ideas To Solve Rear Axle Problem.

    Darkest hour. Maximum teardown carnage.
  6. modulistic

    4.6 Swap Underway. Need Ideas To Solve Rear Axle Problem.

    Roger that. The mounts are right in the way of where the brake lines will run. They gotta go. Will have to weld sn95 mounts to the bottom of the fox frame rails.
  7. modulistic

    4.6 Swap Underway. Need Ideas To Solve Rear Axle Problem.

    Great news. These fox sway bar mounts... Do they need to be cut out? I'm going with the fox control arms so I will need the fox sway bar, correct. Do you know if the 4.6 will fit with the mounts in there. I guess I could get out the tape measure.
  8. modulistic

    4.6 Swap Underway. Need Ideas To Solve Rear Axle Problem.

    Thanks 5l5. a 98 axle materialized out of nowhere, what complications exist when using that axle? entire brakes and wiring harness are going over to the fox. Will stock sn95 rims fit with the sn98, or will I still have outpokage?
  9. modulistic

    4.6 Swap Underway. Need Ideas To Solve Rear Axle Problem.

    progress
  10. modulistic

    Need Egr Help Trickflow Was Worthless

    bastards....
  11. modulistic

    4.6 Swap Underway. Need Ideas To Solve Rear Axle Problem.

    I think this is the ticket. The width from outer wheel lip to outer wheel lip is 68" or so. The measure from fender lip to fender lip is about 68 inches as well. If I roll the lip and the 197 wheel sucks it in a half inch, it should fit barely.
  12. modulistic

    Need Egr Help Trickflow Was Worthless

    step 1 furtively rig vacuum port to a a switch that grounds ignition coil. step 2 car dies when vac applied. step 3 profit
  13. modulistic

    Engine Misfires And More Misfires. Carb Guys Get In Here!

    try a new coil.
  14. modulistic

    2.3 - 5.0

    yeah, the k member is fine. im running a 4 cyl k member with a 5.0 sitting on it. you will need 5.0 mounts.
  15. modulistic

    Fuel Fuel Injectors - Explanation

    oh, and Im running 19lb hr injectors with 8 or so lbs of boost. lots of guys do it. its not good for the injectors though, not a long term solution.
  16. modulistic

    Engine About To Break Transmission Coolings Lines Unless Someone Stops Me.

    put a torch on it and get it hot, then let it cool. repeat that cycle 5 times, spraying oil inbetween sessions. then get it nice and hot and try breaking it. its probably going to break though. might not. definitely need a nice flare wrench. There isnt too much pressure on those lines...
  17. modulistic

    Fuel Fuel Injectors - Explanation

    you could swap it out for 1,000,000,000 lb/hr injectors, you just need to change how long they are open for.
  18. modulistic

    Fuel Fuel Injectors - Explanation

    here, an analogy: think of it like a firehose and a garden hose. lets say I have programmed you to water the grass one second every minute. I didnt tell you which hose you are operating... your only instructions are "open the nozzle at the end of this hose for one second every minute" so you...
  19. modulistic

    4.6 Swap Underway. Need Ideas To Solve Rear Axle Problem.

    "I think it's 14mm vs 12mm but not sure. Basically you'll need sleeves." thanks, good info. I guess I will just have to mock it up and see how it fits. plenty of work to do before that point.
  20. modulistic

    4.6 Swap Underway. Need Ideas To Solve Rear Axle Problem.

    haha, I already crossed the point of no return. If I am reading everything correctly, the 4.6 Kmember will swap in with some minor grinding. the 8.8 sits 1.5 inches wider on each side. the stock 02 bullits come with +30 offset, so to make it stock width, I would need something like +70mm I...
Top Bottom
Back
Forums
Menu