Search results

  1. N

    New SC manifold for 4.6 2V

    The Ford kit looks great, but its backwards for me. Intake needs to face the other way.
  2. N

    New SC manifold for 4.6 2V

    Il buy the eaton manifold if it fits a lightning s/c, I got one laying around for the project.
  3. N

    exhaust for 02gt.

    Use a good penetrating oil, exhaust bolts get tough after bein on a daily driven car for a year or so. You may need gaskets also.
  4. N

    exhaust for 02gt.

    Heres mine... Outside the car... Inside the car... 2 1/4 pipe w/Borla Pro XS mufflers, no crossover/H/Xpipe, stock manifolds and cats...
  5. N

    Modification Survey Thread

    Heres what I need to know, what people are doing to maximize the performance of their NPI engine with a blower. What combination of heads, cams, intake manifold did you use with your blower, a PI engine swap isnt going to be feasible, nor will replacing the NPI pistons to make it easier to use...
  6. N

    Will removing carbon trap cause me to fail emission test?

    Intakes on most cars is a 10 minute job, unless you get a larger MAF, then youll simply need to unplug your chip when you swap back to stock intake.
  7. N

    best plenum?

    If the "Accufab" wouldnt be upside down on my car, Id buy the intake elbow.
  8. N

    Will removing carbon trap cause me to fail emission test?

    I would say move to a free state, and pray california falls into the ocean.
  9. N

    Rear End

    You can get it for free and Ill trade you my 8.8 in 3.55 with auburn diff.
  10. N

    Driving with 4.10's....

    I get sideways a lot with 3.55's, 4.10's would be great! My next track car will definitely have a 4 something gear in the back.
  11. N

    Gear swap...

    No I didnt, but now I believe I have it right. The guy at Killeen automotive told me the other day that it should be tight enough to require a prybar to pull the differential out, so I went and scrounged up .020 worth of shims to make the difference. He said I needed this because of the...
  12. N

    Texas Emissions Laws

    Get inspected outside of Dallas so you dont get the emissions check. Im glad I live in Killeen, no emissions check down here.
  13. N

    Gear swap...

    Im gonna shim it a little tighter Friday night, if the noise persists I will be going to Killeen automotive. The stang guy there told me $125 to set backlash, and $225 if he has to pull the pinion gear to reset pinion depth...both prices include any seals, bearings, shims, misc hardware, and...
  14. N

    any complaints about the SLP setup??

    Too bad they wont take money for a custom job full length headers, and complete cat back with x pipe on my grand marquis...
  15. N

    best plenum?

    +1, best looking TB on the market IMO...
  16. N

    best plenum?

    I actually ran a tenth slower with the chip, intake, and 80mm MAF when I installed it all. Im hoping I make up for the loss with the recent gear and differential swap.
  17. N

    NEED HELP! what rear end gears for viper t56?????

    2000 Cobra R had 3.55 with a T56, if you already have 3.73's I would stick with them.
  18. N

    best plenum?

    My custom superchip didnt do much of anything as far as hp and torque goes, it made its biggest differences with the shift points and firmness of the shifts, it raised my rev limiter about 800 rpm, and deleted the top speed limiter. It supposedly adjusted my fuel and timing, but I didnt notice...
  19. N

    what can a computer tuner do?

    If you have an automatic trans it will reset all shift points to optimum spots in the powerband, providing you get a custom burn or a dyno tune. A off the shelf chip will only go so far.
  20. N

    Kenne Bell Install 10 hours!!!!!!! Done!!!!

    Im in a rut, I want to get the same blower but I also need to get PI heads, I dont think my tax return this year will give me both...
Top Bottom
Back
Forums
Menu