Search results

  1. P

    Pics of 3" tailpipes

    Flowmaster 3 inch tail pipes:
  2. P

    185 on a 6 or 6.5 rim

    5 inch is the recommended width but I wouldn't go past 6inches.
  3. P

    Good Gear Installer In Greensboro, NC?

    Call County Ford in Graham and ask to speak with Thomas Jones or Steve Engle either of them can do it if they can fit you in.
  4. P

    Mustang Spec G-Force 5-Speed Transmission

    Thinking.........
  5. P

    Looking for pics of victor 5.0 intake

    On the 2nd pic, the shiny vacuum fitting on the bottom left of the intake. I ran a pcv valve between the nipple on the oil filler neck and that vacuum fitting. Almost like a closed pcv system. The car ran fine like this while I ran it this way. My new valve covers will have breather fittings and...
  6. P

    show off your engine bay!

  7. P

    Looking for pics of victor 5.0 intake

    Pic of the victor EFI on my 86 coupe I'm using motorsport tall valve covers now and a 3/8 spacer now. No new pics just yet.
  8. P

    Peak HP with Track Heat Top End Kit

    My heads have been decked .030. Combustion chamber is 58cc..My compression ratio is around 9.3-9.5.
  9. P

    Peak HP with Track Heat Top End Kit

    My heads are pedestal mount so that limited how big of a cam I could run. Now if I converted to stud mount and put a cam in with 230/238 @ .050 and .580 lift Then the peak would be closer to 6500-6700. The motor is efficient. I forgot to add I have a electric water pump and race crank. too.
  10. P

    Peak HP with Track Heat Top End Kit

    I use the dyno as a tool basically to see where my a/f is at. I told you what this combo ran on a old full weight coupe I had 6 years ago. 7.40's on hoosier QTP's. Add 20-23 mph to that and that will give you roughly the 1/4 mph. As stated earlier no drag suspension on this car so I dont...
  11. P

    Peak HP with Track Heat Top End Kit

    Notice I said street car meaning no drag suspension. I could take the car to the track right now and it will trap atleast 113-115. But the ET wouldn't be much maybe mid to low 12's. Just because you have a extremely small cam, tb and heads on your 347 and its performance is lack luster. Dont...
  12. P

    Peak HP with Track Heat Top End Kit

    I had a similiar combo 5 years ago using tw heads and the same cam in a 89 coupe. The car made 359 also and it ran 7.40's @ 94 in the 1/8. I have no doubts this car a will run low 12's maybe high 11's on drag radials. I do not have a drag suspension just bbk lowering springs. My goal was to make...
  13. P

    Back to the 5.0 scene

    Make sure theres no rust underneath.
  14. P

    Peak HP with Track Heat Top End Kit

    No track times yet. I just finished the motor last month and had it dyno tuned. The dyno was a dynojet. Combo is Fox Lake stg2 ported brodix heads and systemax intake comp xe276 cam bbk 1-5/8 lt and h pipe Electric Fan accufab (race) 75mm tb w/ 90mm inlet 77 prom 24#injectors 410 gear...
  15. P

    Peak HP with Track Heat Top End Kit

    I beg to differ..
  16. P

    just got a 347 what kinda power should it have

    317.8745
  17. P

    How much for an upper and lower Cobra intak? How much power?

    Hmmm, I have foxlake ported cobra lower and tmoss ported cobra upper w/ 75mm tb opening I was going to install in case my Systemax killed my lowend..
  18. P

    show off your engine bay!

  19. P

    93 Cobra length axles on a 93 gt

    No input??
  20. P

    93 Cobra length axles on a 93 gt

    Here is my problem.I'm going to get my stock 16inch pony wheels widened to 9 or 10 inches. With the back spacing of these wheels (4.8), getting them widened will cause clearance issues on the inside of the wheel well. I will be using a 275 drag radial by the way. (Toyo TQ 275/45/16) Is there...
Top Bottom
Back
Forums
Menu