Search results

  1. H

    Saleen Series IV vs KenneBell 1.7 ...

    The KB wait was about 1 week for me too. Get the 9-psi I.C. kit if you're going with KB.
  2. H

    Southern/Central California Installer?

    Joe recommends Steve at Powertrain. Joe can get you in no problem. Best way to get a hold of Steve is through E-mail. He has always gotten back with me. I wouldn't use Swanson again if that was the last tune shop on the planet.
  3. H

    has anyone else had any problems with panhard bar after installation??

    Click on the link in my signature to see pics of how I dealt with the exhaust and panhard bar issue.
  4. H

    03 cobra bumper on gt/ lights?

    Uhhhhhhh.......'cause it aint foggy?????????? :D :shrug:
  5. H

    03 cobra bumper on gt/ lights?

    Just wait until you get the parts before splicing wires. You can still install the lights without hooking them up if youre concerned about the looks.... or lack of them.
  6. H

    03 cobra bumper on gt/ lights?

    Some who have swapped bumpers have just forced the connectors together to make it work. I choose to go get a splice kit from Ford. It includes the connector with attached wires and heat shrink material to cover the splice. The part number is 1U2Z14S411BA. You will need two. List is about...
  7. H

    panhard bar is in the way of my exhaust..need help!!

    Check out the link in my signature for pics of my car at SoundDomain. Go to exhaust page and you can see what I had done. Hop
  8. H

    KB 1.7 9-psi Kit Owners...Performance Stats Please

    Check out post number 18; it has a dyno sheet also.
  9. H

    KB 1.7 9-psi Kit Owners...Performance Stats Please

    I'm good to go in that department.
  10. H

    KB 1.7 9-psi Kit Owners...Performance Stats Please

    Both of these runs were made with 100 octane fuel on the 9-psig intercooled kit; one run the chip was flipped to Power (91 octane tune) and then flipped to Shootout (100 octane tune).
  11. H

    2003 Cobra rear bumper

  12. H

    Anyone have dyno sheet from stock 99-04 Mustang GT 5 speed

    This is with a Magnflow catted X-pipe and catback system, stock otherwise, manual tranny. 240-hp / 277-tq
  13. H

    KB 1.7 9-psi Kit Owners...Performance Stats Please

    Thanks for posting your information, I really appreciate it. Here is the skinny on my car --------> There are three runs on this sheet: 014 (Blue) = KB kit in "Shootout" mode; 399-HP / 397-Tq (on 100 octane fuel) 013 (Red) = KB kit in "Power" mode; 372.3-HP / 380.6-Tq (on 100 octane...
  14. H

    KB 1.7 9-psi Kit Owners...Performance Stats Please

    I dyno'ed a bit low and I'm curious to know what power level and mods others have. Can you post the KB kit info: (if it's I.C.) Boost level, mods such as the big tube kit and throttle body size, switch chip, gears, and your dyno numbers (Power and Shootout modes) along with octane when you...
  15. H

    couple questions for KB owners

    KB recommends the stock GT pump. It's not necessarily the HP numbers but how you get to those HP numbers, if it's tuned well and no fuel issues arise and you don't live in the high RPM zone the kit will be OK.....but don't expect the motor to last forever. The tune will be fine for the life...
  16. H

    Fix for the non retracting seatbelts.

    Safety equipment has a longer warranty period and extends past the B-to-B coverage.
  17. H

    Full length sub frame connector ?'s for vert owners

    Huh???? :shrug: :crazy: :confused: :crazy:
  18. H

    Full length sub frame connector ?'s for vert owners

    Global West with rocker rail support........the best!!!!!! Look closely, here they are on the car.......
  19. H

    Is the Kenne Bell 75mm throttle body 50-state legal?

    It's not the fender but the wheel well liner that has to be removed for the big tube kit.
  20. H

    How to remove front windshield decal?

    Supplies: Plastic sheeting (like a dry cleaning bag or even Saran Wrap will work). Spray bottle filled with soapy water. Razor blade Spray the decal surface generously with the soapy water. Cover the decal with the thin plastic sheeting. Smooth out any large air bubbles to ensure...
Top Bottom
Back
Forums
Menu