Search results

  1. stanley514

    eq headers are stupid

    Never had any problems installing headers new, used, long, short or equal length etc. Does your car have new engine mounts on it or old worn out stock ones?
  2. stanley514

    Magnaflow too loud?

    Stay away from the Magnaflows. I have a cat back kit behind a 331 drone makes long trips a pain. I have a X pipe & full tail pipes. The mags sound great but the drone suck. I will never buy them again NEVER! I call them ( Magnafarts) to ask about drone (before I bought them) they told me none...
  3. stanley514

    Did your X pipe get rid of drone?

    Stay away from the Magnaflows. I have a cat back kit behind a 331 drone makes long trips a pain. I have a X pipe & full tail pipes. The mags sound great but the drone suck. I will never buy them again NEVER! I call them ( Magnafarts) to ask about drone (before I bought them) they told me none...
  4. stanley514

    quietest exhaust for over 500hp

    Stay away from the Magnaflows. I have a cat back kit behind a 331 drone makes long trips a pain. I have a X pipe & full tail pipes. The mags sound great but the drone suck. I will never buy them again NEVER! I call them ( Magnafarts) to ask about drone (before I bought them) they told me...
  5. stanley514

    Greenwood Auto Parts Poor Head Work Beware!!

    GREENWOOD AUTO PARTS :notnice: :nonono: :mad: :mad: :mad: :mad: :mad: :mad: :mad: :mad: Warning this machine shop is not doing a good work. I took a set of heads to have the springs set up. I told the guys to make sure I had the correct valve seals. I told them that the...
  6. stanley514

    Warning Greenwood Auto Parts poor work!!

    GREENWOOD AUTO PARTS :notnice: :nonono: :mad: :mad: :mad: :mad: :mad: :mad: :mad: :mad: Warning this machine shop is not doing a good work. I took a set of heads to have the springs set up. I told the guys to make sure I had the correct valve seals. I told them that the...
  7. stanley514

    Electrical gurus please help.

    Well its running. I bought a Breakout box. I checked everything with it. I didn't find any shorts. So I installed a Good used computer. The car started the first try. I have drove in about 120+ miles no problems yet. I installed 2 rebuild P.O.S. computers from Advance. The car with both...
  8. stanley514

    Electrical gurus please help.

    Ok the fuel pump won't stop. It is making pressure. I have replaced the relay. I installed a new pump trying to fix this problem. The old pump was a Walbro 155lph I installed a Walbro 255lph. The plug ins were the same I just plug up the new pump. Could this wire be grounding the wrong side...
  9. stanley514

    Electrical gurus please help.

    Ok per jrichker. Less than 12ohms with EGR, MAP and TPS connected or disconnected. My Diagnostic schematic says I have service short to ground replace ECM? I've already done this and blown a 2nd ECM??
  10. stanley514

    Electrical gurus please help.

    I have a OTC 4000E made by MAC. Can't get any codes from the ECM at this time. Stanley514
  11. stanley514

    Electrical gurus please help.

    Thank you jrichker. I will let everyone know what I find. Stanley514
  12. stanley514

    Electrical gurus please help.

    Ok I have replaced all the normal relays EEC,Fuel Pump etc. My 92 Has blown two ECMs. I feel I have a dead short to one of the sensors. Where should I start looking for a short first? Or where can I find a diagram of what to check first? If anyone has had a dead short and found it how...
  13. stanley514

    Car won't start

    Won't start? Ok I'm driving down the road and boom my car shuts down?? I had aready replaced the TFI and Fuel pump 2 years ago. It ran fine till now?? I have 3/4 a tank of gas. I replace the fuel pump relay and the ECC relay. Then I replaced the TFI Module. I have a spark its kinda red not...
  14. stanley514

    Car won't start

    I have fire and fuel. I have changed the ECC and fuel pump relays the Fuel pump and the ign mod on the dist. Still the pump just runs nonstop.
View older results
Top Bottom
Back
Forums
Menu