Search results

  1. wp331

    FS comp magnum steel roller rockers

    1.6 ratio rebuilt by comp good condition. For 7/16 stud. Poly locks included. 100$ plus shipping. Can text pics if needed. I live in sw Washington state
  2. wp331

    For sale AFX wide band a/f monitor

    Used in good working order. Factory box. Five wire sensor. Red digital display. 150$ plus shipping. Can text pictures. I live in sw Washington state.
  3. wp331

    03/04 cobra high capacity front heat exchanger and tank

    Fluidyne front heat exhanger, used in good condition 150$ plus shipping. Canton racing super charger coolant tank. Mounts in place of battery, used ,only tank no hard ware 80$ plus shipping. Can text pics if needed. I live in sw Washington state.
  4. wp331

    For sale ford nine inch detroit locker

    Detroit locker for nine inch ford. 35 spline used in good condition. 250$ plus shipping. Cant text pics. I live south west Washington state.
  5. wp331

    2008 bullitt axle back

    Stock axle back took off my Bullitt @ 20,000 miles good condition some rust on hangers. will text pics if needed. 100$ plus shipping. I live in South west washington state
  6. wp331

    2008 Bullitt mustang springs

    Good condition 125$ plus shipping all four. About 15000 highway mile on them. Approximately 5/8inch lower than stock and slightly stiffer. located southwest wash state
  7. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Vernon ported the R intake. Actually smoothed it out pretty good. He is pretty skilled at porting heads so the intake was low challenge stuff or him...
  8. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    No trouble at all. Hope it helps...we KB addicts need to stick together!:cool:
  9. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Shawn, I got the outlet off the blower and the pattern you wanted. Pm me your address and i will mail it! Getting closer to putting my beast back together. I am getting the racing jones already and it is only feb!
  10. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Mine peaked @ 6300 with big hyd roller. Will peak around 7000 with new mech roller cam. Mod motor cars make power out to 8000 with KB blowers. The 2.1 KB runs out of cfm on a bigger ci motor at higher rpm's. My 2.8 makes full boost @ WOT no matter the rpm.
  11. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Depends on how aggressive you pulley it. Remember boost is not the end all with making power. It has been shown many times that a larger blower making slightly less boost at the same rpm as a smaller blower is likely moving more cfm and operating more efficiently, thus making more power. With as...
  12. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    No rear support. The cross over iks really beefy, as is the box that the cross over bolts down to. I don't recall the aluminum grade of the cap. It is at least 3/16 thick with support beams on the inside . My top cap is a lot bigger than your design requires...3/16 without supports should be enough.
  13. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Shawn, Careful about how thin of aluminum you use to recap it. That sound is cool but it is the pulse of compressed air coming out of the blower. If you spend a lot of time at wot or repeated wot cycles...aka drag racing those hot, high pressure pulses tend to pulverize aluminum and crack...
  14. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Hey Shawn, nice to get to know you. My fuel system feeds into the pass side front crosses over to the driver side from the rear of the passenger side rail and exits to the regulator from the front of the driver side rail.... no issues as of yet with 83 lb injectors...
  15. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    The FAST efi is a DFI style engine management computer ...no maf required
  16. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    The fast is classic bank to bank with wide band 10 years old..and yes it was 27 degrees of timing
  17. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    No problem. I ran up to 27 degrees total with c 16. Never came close to that on 100 octane and water meth. You will find the intercooler will work better without the fiber glass bumper, it will get better air flow.
  18. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    usual wit? or lack thereof ......there feel better now?
  19. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Foggy spotlight! Got it Vernon!
  20. wp331

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    92ROHCP, Intake temps are currently running 130-140 on hot days with 20lbs of ice on each pass in the cooler box. My car hasn't been dyno'd in two years. I have found that getting a baseline tune on the dyno after big changes is helpful only to the point of doing a shakedown. As soon as...
Top Bottom
Back
Forums
Menu