Search results

  1. 67GTCOUPE

    Converting from 4 speed to auto?????

    Actually we are buying a 1994 GT convertible.....AUTO :banana: SOOOOOOOO...my 4 speed stays in the 67!!!!!!! :nice:
  2. 67GTCOUPE

    Converting from 4 speed to auto?????

    Well we are lokking at a 94 GT convertible that is mint and auto!
  3. 67GTCOUPE

    Converting from 4 speed to auto?????

    No, I would be keeping it, along with the original motor....in my shed, in case I ever sell the car.
  4. 67GTCOUPE

    Converting from 4 speed to auto?????

    My wife doesn't drive manual tranny cars.....so I am contemplating swapping the toploader for a slushbox :rolleyes: I know, I know. Any way......I have a 67 with a 410hp and 400+ft/lb 351w in it......what would be the best trans to pop in and what do I need? I figure I need a new...
  5. 67GTCOUPE

    Will a 1970 gas tank fit my 67????

    I saw an article in a mag recently that said a 1969-73 gas tank would drop right in, inplace of the stock one in 1967 stangs??? The bonus is it is 20 or 22 gallons. You apparently need to bend the filler neck on tank a little??? Anyone do this or know about it?
  6. 67GTCOUPE

    Catostrophic tranny failure on dyno

    Guess you will be installing a driveshaft saftey loop?
  7. 67GTCOUPE

    351c or 351w?

    I need to disagree with some of what you say. Every comparison dyno run I have seen......three seperate ones which compare similar windsor to clevelands......HAS SURPRISINGLY shown the windsor is MORE POWERFUL! Not only in peak horsepower, but it kills the cleveland in torque......in fact...
  8. 67GTCOUPE

    351c or 351w?

    Windsor all the way. Surprisingly, the windsor makes more power than the clevland in a recent mag I have....that is two versions of the clevland. Anyway....windsor has parts you can get anywhere. I am very happy I sold my clevland and went with a windsor!
  9. 67GTCOUPE

    67 Wiper Motor Tricks?

    It is the linkage where it mounts to the motor......you need to take it off and reverse it then check it is ok.
  10. 67GTCOUPE

    67 Wiper Motor Tricks?

    dude it is a crappy job........done it a few times :rolleyes: Take out the instrument cluster and work through the opening..........BE CAREFUL very sharp metal edges...I wear kevlar arm protection sleeves. ALSO: DO NOT DO WHAT I DID......I had the wipers 180 degrees out of...
  11. 67GTCOUPE

    Griffin radiators

    I put a griffin into my 67. I cannot get photo at present time. All I did was go to scrapyard and get some bottom rubber mounts out of a mid 80's f150.....cut two slots into these so the griffin fit into it. Then get a heavy guage aluminum plate and bend it so that it is about 90...
  12. 67GTCOUPE

    Where to buy new strut rods??????

    After hearing about the snapping strut rods.......I want to replace my 67's rods with aftermarket (safer) pieces. Where is the best place to get a quality set for the least $$$$$$??? Thanks
  13. 67GTCOUPE

    is my carb to big???

    I disagree. First off the carb is a quasy vac secondary......so it should be ok with your motor......but it is a Carter/Edelbrock, so it is a mystery how to fix it or set it up. Personally: I really suggest that you do yourself a HUGE favor and get the Edelbrock performer RPM cam and...
  14. 67GTCOUPE

    good vendor for rims?? (and another backspacing Q)

    I would seriously look into it before you order. I had to sell my AR S-200's because they were the wrong offset for my 67! Fricken AR SUCKS for customer service!!!!!! I will never, repeat never, buy another thing that is made by AR!!!!!!! They have 3 3/4" backspacing on most of their...
  15. 67GTCOUPE

    351W Setup

    Do whatever turns your crank. Personally I equate putting money into any stock head=to wiping your arse with $50.00 bills! It is the best example of TURD polishing that there is........except maybe all those guys who swear by the used edelbrock carbs off ebay.....but that is another fantasy.
  16. 67GTCOUPE

    H-Pipe costs HP

    I just run straight pipe to mufflers after my headers.....old school, but it works like a charm for me!
  17. 67GTCOUPE

    351W Setup

    You are MISSING THE POINT. Go with brand new Aluminum heads! 1) Saves 75 to 100lbs!!! That equals free horsepower equivilant. 2) Maxed and I mean Maxed out modified stock heads flow where the aluminum aftermarket heads start out of the box! Now, give the Edelbrocks a simple cartridge...
  18. 67GTCOUPE

    Carb recommendation?

    To the point I made about Edelbrock carbs.........they are OK....no more, no less. One thing about them is they are STUPID SENSITIVE to fuel pressure! If you run at 6 psi or above........you will run into problems with flooding, bogs, and in some cases, raw gas filling the seconday side...
  19. 67GTCOUPE

    Carb recommendation?

    Ya........and what you will get 90% of the time is some POS that didn't run right on someones car for whatever reason! Edelbrock isn't all that good of a carb........I know, I had one! :notnice: Instead of throwing $100+++ at some used or supposed rebuilt POS on ebay.....do yourself the...
  20. 67GTCOUPE

    Carb recommendation?

    Good decision! Call and talk to Marty Brown......he is owner....he knows his stuff!!!! He can actually custom tune it for your specific engine (it would cost a little more though?). Any way tell him Mike from Thunder Bay sent you! I have dealt with him several times, and he has been...
View older results
Top Bottom
Back
Forums
Menu