Search results

  1. BPA

    Going Kenne Bell (again)

    how much u pick it up for?
  2. BPA

    charging question

    if u have a clamp style meter u can load test ur charging system and also check out ur voltage as well and make sure both are within specs. got a battery charger? see if the battery is sulfated as well if they say the battery checks out on the hand held tester. Make sure all ur grounds are good...
  3. BPA

    Whats with this POS car!?!?

    Check the codes like they said, then if none are present buy a fue pressure guage and determine if ur issue is spark or fuel related. and go from there ...
  4. BPA

    Ford SVO coil fitment Question

    I was going to buy the Ford Racing High Energy E-Core Ignition Coil, pn FMS-M-12029-E351 and wanted to know if it would mount up to the factory coil location without any modification. Anyone buy it and know? I was looking at the mounting bracket and didnt think it would . I like the chrome look...
  5. BPA

    Who would do HCI over a SC??

    Boost it and install it yourself. Isnt worth the 800 in labor.. want more power after that. get a power pipe ... then some smaller pullys.. still not happy.. get the afr's u wanted. You dont have to get a dyno tune eather right off the bat. The kit comes with everything u need to make it run...
  6. BPA

    vortech install ?

    It was a tight fit and i had to loosen the alternator bracket the small ajustable sliding one to get it to fit but the one they supplyed worked. for the elbo i sprayed it down with some wd-40 and it slid on you might have to mark the angle u want it sitting at and use a rubber mallet and gently...
  7. BPA

    charging problems: search function not helpful

    see if u have voltage at the bk/o wire, that goes from the fusable links to the alternator. should be battery voltage.
  8. BPA

    charging problems: search function not helpful

    the igniter wire unpluged from the alternator should have approx battery voltage as well. check out those things and rule out the alternator and then fault trace your problem further is it isnt fixed..
  9. BPA

    charging problems: search function not helpful

    test lights are not good for deciding if an alternator is bad...well here is what i would do... check all of your grounds , remove any to the body or engine and clean them so there isnt any corrosion on them.these will weck havic on your charging system. then check battery voltage @ idle, then...
  10. BPA

    vortech install ?

    thats the abs module bracket your talking about has the module with tubes running into it?. loosen up the screws on it and use a pry bar to hold it in place while u tighten it down to give u the added room. You could also elongate the holes for the bracket as well. dude go to the hardware store...
  11. BPA

    is 30 psi ok for 18's?

    tire should say min and max psi on it. Personally on an 18 id run 32- 36 psi depending on how they start to wear
  12. BPA

    what would you do next?94 gt

    get some gears , then save up for eather a supercharger or heads and cam later down the road . dont waist ur time or money on the small stuff u arnt going to notice to much of a gain on pullys and stuff like that. not really cost efective when u add all that up.
  13. BPA

    do i need an FMU w/ s-trim?

    good luck with the install , im sure you will be happy with the setup :) let us know how it turns out for ya.
  14. BPA

    S.F. Bay area meeting

    any mustangs would be more than welcomed.
  15. BPA

    S.F. Bay area meeting

    actually maybe this is better suited for the talk area.
  16. BPA

    S.F. Bay area meeting

    Id like to hold a S.F. bay area 94-95 mustang meeting were we could all check out each others cars and shoot the chit. Would anyone else be interested in something like this?here is the tech part.. i need some ideas on supercharger setups sence i just finished mine on the best location for the...
  17. BPA

    oil capacity for 94 gt

    you could always drill and tap two new drain holes if you dont have the proper tools to get the existing plugs out. another option would be to use a punch instead of a drill sence it would help create some extra threading material and then tap it. :D
  18. BPA

    oil capacity for 94 gt

    yes i would also make sure that u take out not one but two of the oil pan plugs.
  19. BPA

    nissan 350z ?

    ok i found out they are suposed to have 285 or so hp and do 0-60 in 5.5 (i.e motortrend crappoa) i got to ride in it today and we did a short little race to about 60 or so against our other buddys 95 gt from a dead stop. pretty much dead even all the way up. seemed to me like a mid 14 secound car.
  20. BPA

    How To Do A Compression Test On My Car?

    take all the plugs out... make sure u get compression on each cylinder 3 times and then go to the next cylinder.
Top Bottom
Back
Forums
Menu