Search results

  1. C

    steeda pullie install questions!

    If you can use a impact gun to remove the crank bolt, life is much easier.
  2. C

    Cervini Quater Panels and Side Scoops...

    Emay, your car looks awsome. My car is black also and it's a real pain to keep clean, but I find the California duster works great if you have good coat of wax applied. What kind of wheels do you have, can't quite make it out from the picture. The offset looks perfect.
  3. C

    Cervini Quater Panels and Side Scoops...

    I have the lower and upper side scoops, but I think I like the looks of the flush mount side window louvers better(I'm not sure who sells them, I've only seen pictures) and there cheaper too!. As for the whole cervini kit, I have the cervini Ducktail Spoiler and have a problem with the center...
  4. C

    Problems after applying tune

    If you can, drive it for 3 or 4 days. My car did the same thing when I first progammed it , but it stablized in a couple of days and has been fine ever since (over a year now)
  5. C

    Front suspension "clunking" issue?

    Thanks Jenn, The sway bar attaching brackets look good to me but I will keep an eye on them. I have the same clunking noise with the Roush componants as I've had since day one with the stock suspension. I did notice however when installing the Roush stuff that where the strut goes through the...
  6. C

    Front suspension "clunking" issue?

    the popping noise is a different issuse from the clunking noise, but i do agree that the upper bearing is a cheap design and perhaps replacing this will fix the problem. I have wasted too much time chasing this problem. Ill wait unitl ford comes out with a fix before I do anything else
  7. C

    Front suspension "clunking" issue?

    I hope the solution is something other than replacing the struts, as I have installed the complete Roush suspension kit and still have the clunking issue!
  8. C

    Does any body here NOT have the infamous front suspension thunk?

    I installed a complete roush suspension kit and the clunk is still there!
  9. C

    Parnelli Louvers

    Does anyone know if the rear window louvers that are shown on the Parnelli car are avaliable from the aftermarket. Most of the louvers I have seen have 6 quite large louvers pieces, but the Parnelli unit has 7 smaller louver pieces which is what I'm looking for.
  10. C

    Loud Sloppy Clatter in 05 GT

    I had a loose kind of clattering noise coming from under my car and I honestly thought I had tranny problems, but what it ended up being is the metal retainers for the rubber exhaust pipe mounts at the trans bracket location. They rattle when driving the car and it gets worst the colder it gets...
  11. C

    Front end Clunk

    If someone figures it out please let the rest of us know. I have tightned everything in sight and still had a slight clunk at the passenger side front. I installed a complete Roush suspension front and back, the car handles awsome but I still have a slight clunk in the front end. Large bumps are...
  12. C

    4:10 questions

    Hi all, Can anyone tell me what RPM @70 MPH they are turning in 5th gear with 4:10's(manual trans) and also when you had the gears installed, would the car run good enough for the installer to test drive it without it going into limp mode. I have an XCAL and would rather do the computer work...
  13. C

    LCA Opinions

    My car is lowered with a complete Roush suspension swap. I have not installed an adjustable panhard bar, as lowering the car only a inch or so did not shift the rear end over enough to worry about. I measured the wheels form the outer wheel wells before and after the car was lowered and could...
  14. C

    LCA Opinions

    Thinking about installing LCA,s but because there are so many different designs, I would like everyones experiances and opinions with the LCA's that they have installed. I'm not going for bling and I don't really care what they look like, I just want the best performance at a reasonable price.
  15. C

    Roush suspension in

    Took me a Saturday to install but is well worth the time and cash. The drop was noticable but not extreme, about a inch in the front and slighty more at the rear. The ride is just a little bit firmer than stock normal driving, but when pushed, it goes right where you point it. Best of all that...
  16. C

    Why is my brand new car KNOCKING?

    It could be a cam phaser noise if the noise goes away above idle. I believe there is a TSB covering that condition. Check it out.
  17. C

    Something loose in front end.

    Some new clues. Lifted the car up and placed a lever under the tire then put the car back on the ground. Jumped up and down on the end of the lever working the front suspension and found absolutly no noise what so ever from the outside or from the inside with someone else doing it. Jacked the...
  18. C

    Something loose in front end.

    I'm starting to think that the clunking is coming from the strut it's self, perhaps the noise is the valving or some other internal componants working inside. If some other members are out there that have replaced their suspension, maybe they could let us know if the problem went away. I think I...
  19. C

    Something loose in front end.

    I have the same noise since car was new. I have stock front end. The slight clunking noise over small sharp bumps is really annoying, and the only problem I have with the car. I would like to fix this myself, as past dealings with dealerships have not been that great. I wonder if the addition of...
  20. C

    steeda tri-ax short shift v. hurst SS?

    Ford Racing also make a short throw shifter. it looks like an oem shifter. It might be less noisy.
Top Bottom
Back
Forums
Menu