Search results

  1. scalder

    Best Tire Sizes for Drag radials

    If you heat them up properly they hook just fine..but they need a good long burnout.
  2. scalder

    Best Tire Sizes for Drag radials

    Definitely 275's (nitto only) on the stock rim...like everyone says, nittos' run narrow. They look PERFECT!
  3. scalder

    What Is Wrong With This Car?

    I was about to say traction control was on...no clue here brutha. So this response is worthless....ttt for ya though.
  4. scalder

    Going to install Gears! cost and ?? 3.73's or 4.10's ????

    If memory serves me it was 104'ish...couldn't tell you the exact RPM but still had room. Normally I pay a lot more attention but had a wedding to go to that afternoon so I just made some quick shake down passes to make sure I wouldn't have to shift to 5th.
  5. scalder

    Going to install Gears! cost and ?? 3.73's or 4.10's ????

    Nope....I was afraid that I might but made a few passes last year with no problems..
  6. scalder

    Going to install Gears! cost and ?? 3.73's or 4.10's ????

    Ah do 4.30's now....that way you'll never have buyers remorse. Only if you're staying N/A though..
  7. scalder

    Going to the track sunday...

    Found this somewhere, some time ago. Just copied up to this point. My one piece of advice is not to worry about your reaction time, it has no bearing on your ET....Good Luck and post up the times/slips when you get back. Since this is for beginners, I will assume you are on street tires. DO...
  8. scalder

    Going to the track sunday...

    Slowly??
  9. scalder

    Going to the track sunday...

    No burnout required. Just drive around the water box and light em up long enough to dust em off. I don't know, I guess like you're showing off at a traffic light or something.
  10. scalder

    fox body springs

    They are different. Put them on the front and just run your stock rears until you get the ones you want. I drove that way for 6 months...
  11. scalder

    Are lca's hard to install for a novice installer

    Well then, it’s not too difficult a job. Get the back of the car supported on jack stands and remove the rear wheels, disconnect the E Brake lines where they mount to the sway bar, unbolt the rear sway bar, disconnect the shocks at the LCA, put a floor jack under the LCA where it supports the...
  12. scalder

    Are lca's hard to install for a novice installer

    I completely understand. Do you have isolators on the car right now? That would help some if you don't.
  13. scalder

    Are lca's hard to install for a novice installer

    Why are you putting the stockers back on?
  14. scalder

    Bassani Question

    Crew_dawg16 let me give you a little bit of advice...do NOT run the Bassani O/R X with MagnaPACKS...Not sure how they sound w the Magnaflows but they sound like arse w the Packs. Just an FYI...hope I didn't offend anyone!
  15. scalder

    am i shifting correctly?

    Get a set of good LCA's and that will help a LOT!
  16. scalder

    04 Spoiler removal

    There are 2 different plugs you need since the holes are different sizes....Get the Hillman nylon hole plugs in 3/8 and 5/16...the part numbers are #139461 and #139442...
  17. scalder

    What size tires

    A 275 Nitto fits nicely!!!
  18. scalder

    Nitto dr555 275/40

    17 psi for the DR's...don't forget to bump the front tires up to 45 psi or so....
  19. scalder

    1/4 question

    Heat those DR's up real nice and considering how much you spun before, you should be able to knock off a half second or more. I went from a 13.5 to a 13.08 with just the addition of the Nitto's! What were your previous 60 ft times? A lot of improvement can come just from practice alone...
  20. scalder

    4.10 Gear videos in daily driving

    Just go 4.30's and be done w it!
Top Bottom
Back
Forums
Menu