Search results

  1. D

    Camshaft change opinions on a stroker

    Im asking cause my combo is about the same except it has dometops a lil more compression ,and efi
  2. D

    Camshaft change opinions on a stroker

    So how did you like this combo w/the 282? Did it make all that power?
  3. D

    Camshaft change opinions on a stroker

    I like that hp rating. 455hp with a 282 and afr 185? Whooosh....I gotta get to a dyno
  4. D

    intake gurus,is this too big 4 me?

    Like I said...I can floor it...and just pump the clutch at 6000 to shift..shelll jump to 7000,73 maybe "cause im real fast"withthe gas to the floor still and keep her up in that range and I kill anything next to me. If i granny shift and let rpms get under 25 the power dont come back until she...
  5. D

    intake gurus,is this too big 4 me?

    I have a victor efi it says 4000to8000 rpms now whats suppose to happen beneath 4k? I have sluggish power beneath and its aggrivating. My question is...are these made for racing only? when i get to 3k rpms the car starts to come together real sweet and it pulls wayyy into the red zone...
  6. D

    Update: 03 Cobra 6th Gear Vibration

    ?????????????update 2yrs?
  7. D

    flywheel metal melted what is this?pic

    http://www.corral.net/forums/showthread.php?t=811871
  8. D

    Help w/ High Speed Vibration

    why remove the dogbone? gotta make sure the rears good,the driveline angles are correct and the u joints are good.tranny hieght is also critical,vert and horiz if you revoved the motor also. the stocl motor mounts on my car had shims on both sides
  9. D

    Serious problem w/tko Need opinions really bad

    Man!!! 3 hours on a lift and I found that my brand new ujoint caps were a hair too small and the driveshaft was freekin out. Thats after I put a new shaft in w/the new u joints ,pulled out and it was worse and i was pissed. Then finally found that u joint thing. Now I get like zero tranny...
  10. D

    Serious problem w/tko Need opinions really bad

    the angles are critical. I found that when you bolt the exhast back up it really holds the tranny in one spot. The hieght of the tranny and rear pinion has to right. They do that with an angle finder,then shim the rear arms and/or trans mount to get it right. The vib you have sounds like it...
  11. D

    msd 6al users,white wire goes where? and

    I GOT IT..THE STOOOOPID ARSE MSD WIRING MANUAL FAIls TO SAY THAT harness they show,where the white wire goes ,is the actual pl,ug that goes into the coil they show the coil and a another plug,but they dont say the other plug is the coils plug that you unplug.making us think what is this???
  12. D

    msd 6al users,white wire goes where? and

    help!! where does this white wire goto? and the wires on the coil get tapped into? Also the coil has a red AND red/grn stripe as power,which gets used? anyone know where to get the switched 12v from? please be specific,the msd instructions dont help me at all.
  13. D

    $169 3 1/2 in Summit Radiator FITS our cars!!

    who got pics of this installed? anyone? It sounds like the fan is gonna be a headache to mount?
  14. D

    Hi speed fan ?

    hissin,have u learned any of this yet? I need info on this controller thing also,actually i just need the pinout diagram.95 eec aode
  15. D

    Need eec pinout for fans on harness"diagram or any info"

    im using a pih kit,and a x3z processor on an x aode which is now a tko. But the stock 95 aode harness pinout is what i need,because i need to know which wires do what. Because...my fan controller stays lit up on high speed as soon as the key is put on. I need to wire it up somehow the right...
  16. D

    Need eec pinout for fans on harness"diagram or any info"

    I need to know which wires do what on the harness,im using a pih kit and having fan issue if u have a diagram email it to [email protected] please
  17. D

    rad cams,high compresion, vibration 3500rpm help

    I dont know man.I got the motor complete. The reciept said high performance balancer "maybe cobra?" But Theres a chance someone swapped my balancer and put a stocker on.It dont make sense to me either.But my motor was at a "friends"house for a couple months b4 I put it in,and he wanted...
  18. D

    rad cams,high compresion, vibration 3500rpm help

    I dont know what is was balanced to but it was correctly done/ 300 stroke fms crank grind 010 010 w/bearings decked 007 both sides line bored etc etc eagle sir rods kb pistons fly cur for reliefs fms flywheel main girdle cloyes roller arp oil drive I believe its a 306 will a...
  19. D

    rad cams,high compresion, vibration 3500rpm help

    I need some input. xe282hr cam dometop 11.5.1 vic efi intake rpm 202s long tubes stock balancer. billet flywheel,dual centerforce moroso drag pan,main girdle etc etc The engine revs smooth as silk up 3500 plenty power exactly 3500 it starts vibrating and smooths out a little as...
  20. D

    Tremec tko install complete

    I asked becuase I get good vibration thru the shifter,and more in the upper rpms. and more rattle than I can bare to hear. I put the yolk in the tranny by itself,and the tranny is com pletly ABSOLUTLY SILENT THRU ALL GEARS w/out the driveshaft. no vibration at all. whats that mean? IM...
Top Bottom
Back
Forums
Menu