Search results

  1. I

    C&L plenum gaskets and hardware

    No, just reuse the stock one at least on the intake side (its more of a rubber O ring than a gasket). I changed throttle bodies when I installed mine and the new throttle body came with a gasket, however the stock one was in good shape and could probably be reused. One word of caution my stock...
  2. I

    Aluminum Driveshaft Question

    I had mine installed at the same time as my new clutch, I did not notice any change in performance, but I was getting used to the new clutch. Vibration might be a bit better, again its hard to say for sure. Ike
  3. I

    Where can I find 40th Ann. style stripes?

    Speaking as someone that has been in the vinyl sign business , the cost of the vinyl is a small part of having vehicle graphics installed, even the most expensive metalic vinyls rarely cost over $60-70 for a 15 inch x 5 yard roll. The real money goes to the design layout, and installation, to...
  4. I

    Install price on clutch

    $175 + $40 to resurface the flywheel (I called around and was quoted between $165 - $300)
  5. I

    Please Help Driveability Problem

    No update yet, we have been having warm weather (the low last night was in the upper 50's). Ike
  6. I

    Nervous about installing pullies and t/a

    As has been said before, the only confusing part is keeping up with which crank bolt to use when. If you tighten down the long "starter" bolt you will dammage your crank. Ike
  7. I

    '98 & '99 GT owners, when was your car built?

    My cars production date is listed as 11-25-98 (according to the local Ford dealers warranty paperwork) The sticker on the drivers side of the engine has a date of 10-29-98. Ike My VIN ends in 107XXX , from the research I have done, this implies my car was one of the frist few thousand 99...
  8. I

    steeda timing adjuster

    The Steeda timing adjuster relocates the crank position senesor allowing you to fool the comptuer into advancing the timing by means of a rotateable cog wheel. Ike
  9. I

    Bolt Ons

    Nothing worth doing, most things worth doing start around $150. (shifter, pullies, o/r X/H pipe, Control arms, timing adjuster, sub-frames, strut tower barce, springs(minimum wihtout new shocks, c/c plates, etc)) Ike
  10. I

    Spending $500-$600

    Shifter first, then Springs and shocks, plus the usual things that may go with that (caster/camber plates if you drop much), offset bushings, etc. if tis in the budget Ike
  11. I

    spring isolater, and some?

    They are the rubber pieces that keep the metal springs from touching the metal suspesion parts. When I installed my springs last summer, the stock front isolators were still in good shape, but the rear ones were not, I did not have any replacement ones at the time so I had to reuse them anyway...
  12. I

    Transmission opinion

    I don't think I have EVER seen a thread on Stangnet with so much wrong information in it. 96-98 Mustang GT T-45 with mechanical speedo sensor 99- Mid 01 Mustang GT T-45 with electronic speedo sensor Mid 01+ Mustang GT T-3650 96-98 Cobra T-45 (same as GT) ? 99 & 01 Cobra T-3550...
  13. I

    how much to install clutch

    I paid about $175 plus $40 to have the flywheel resurfaced, to have mine done at a local reputable transmission shop, when I called around I was quoted from $165 - $300. The main reason I did not try to do the install myself is my only free time is over the weekends, and there is nowhere here...
  14. I

    Help Me Remember!

    You are talking about cut-outs, I am sure there are several brands, there are some listed at www.thunderracing.com called Flow-Tech's by Holley Ike
  15. I

    Excuse My Ignorance

    Yes, 99+ models use an electronic sensor with no gear. Ike
  16. I

    Please Help Driveability Problem

    My OBD-II scanner is in, I hope to start logging the activity on our next cold morning. Ike
  17. I

    OBD-II TPS Sensor issue?

    Thanks, its always nice when people have real numbers. Ike
  18. I

    How come nobody makes Roush wheel replicas?

    I still think its likely a Trademark issue, there are two posibilities that I see, First Saleen is technicaly a manufactuers, and Roush is a customizer. Meaning Saleen buys cars from Ford under a special agreement, then sells them as if they made them. Therefore laws that insure the supply of...
  19. I

    original battery life

    Mine is starting to get weak, 99GT built in Oct of 98. As to the sudden battery death, it happens, a number of years back I had a fairly new battery die on me while I was stopped at a gas station, it went from working fine, to completely dead instantly. Ike
  20. I

    How come nobody makes Roush wheel replicas?

    I suspect its something to do with not wanting to get sued by Roush for trademark violation
View older results
Top Bottom
Back
Forums
Menu