Search results

  1. I

    t-45

    One note, the T-45 up to '98 used a mechanical speed sensor, the 99+ used an electron ic speed sensor. Ike
  2. I

    Accufab throttle body question ???

    I wrote an email to Accufab about their TPS, asking if it was the same as the factory Ford unit, and never heard back from them. Ike
  3. I

    do the t-45's use a speedo gear?...if so, what color for 4.10's

    To answer your question it depends on the year T-45 for up 98 models were mechanical (used a gear, T-45 for '99 and later were electronic. Ike
  4. I

    Question about throttle body swap

    I first tried using a good screw driver with no luck, then cut a slot in one screw using a cut off disk, unscrewed it with a flat head driver, that did not work on the second screw, so I just ground the whole head off. Ike
  5. I

    Cheap PI Heads

    Karkraft.com has a combo deal now on take off PI heads and intake for $480 they claim these are 01+ heads with 20-30,000 miles. Ike
  6. I

    Is the Plenum install pretty straight forward?

    It involves removing and replacing about a dozen screws, just make sure you don't drop anything down the intake, don't over tighten the screws on the intake (remember that it is made of plastic). If you are also changing out the throttle body be aware Ford uses ver strong locktite on the TPS...
  7. I

    Autotap, is it worth it?

    Check out scantool.net I have one of their PWM units for my Mustang, some software is better than others. Ike
  8. I

    Cold Air Intake with Pro-M MAF?

    Anyone else? Ike
  9. I

    Cold Air Intake with Pro-M MAF?

    I have an aftermarket 80 mm Pro-M MAF, and I want to get a CAI (I know its not going to add much HP, but every bit helps). What do you recomend, and will the FIPK or the Densecharger work with my MAF? Thanks Ike
  10. I

    Where does

    You need to jack up the rear of the car with the rear suspension unloaded (wheels hanging in the air) the pinion snubber is bolted to a small metal box, you must unbolt the metal box from the car to get to the nut on the back of the stock snubber. Basicly unbolt the metal box with stock...
  11. I

    How long did it take you guys to install springs

    One note, you can drive your car with just the front or rear springs installed. When I did mine I had to drive mine for about a week with just the rear springs in due to bad weather rolling in earlier than expected. Ike
  12. I

    idle help needed

    Have you checked/changed your IAC? Ike
  13. I

    Anything special i need to know before changing throttle bodys?

    The only really hard part is removing the TPS from the stock one, the locktite Ford uses on the screws is some real strong stuff and the screws are phillips heads. I was able to get one of mine off by cutting a flat slot into it, the other I ended up grinding the whole head off. Ike
  14. I

    99 35TH ANNIV HOOD SCOOP diff from 01???

    Ford had a problem with the 35th anniversary scoops coming off, so they added more screws to the '01 style, I am not sure on the specifics of the size difference. Ike
  15. I

    Buddy's 4.6 NEED's HELP!!!!!!!!!!!!!

    I think you are wrong on return/returnless fuel system, the Mustang did not get a returnless fuel system until '99, I doubt any other 4.6 cars had it much sooner. Ike
  16. I

    Ford recall for 2002 GT

    There was a guy online either here or over at the coral a couple of years ago that lost his Mustang to an electrical fire from the dashboard area. The car was at the Ford dealer having work done when it happend (engine work if I recall correctly), and they replaced it. If memory serves...
  17. I

    SOHC to Mach 1 engine???

    Just a note here, there is a lot of talk in this thread about stronger internals. This may or may not be true, but there was a thread here a while back pointing out that only the manual transmission Mach's have the forged crank, the automatic transmssions ones don't (Ford cutting cost on us...
  18. I

    Steeda Timing Adjustor and U/D Pulleys

    You might be able to remove the alternator pulley bolt with a strap wrench holding it in place, if you have one you could always try it and see, it only takes a couple of minutes to remove the belt from the alernator. If not most auto parts stores have electric impact wrenches they will loan...
  19. I

    Please Help Driveability Problem

    I think you may be right, it seems to be reading air temps. higher than I would expect, I am going to hook up the computer this weekend when it turns cold again and see what it reads as intake temp. Ike
  20. I

    Need New Windshield with Running Horse?

    thanks, the part number certainly helps Ike
Top Bottom
Back
Forums
Menu