Search results

  1. Messed up blinker

    Messed up blinker

    • Imatk
    • Media item
    • Comments: 0
    • Album: JPics
  2. JPics

    JPics

    • Imatk
    • Album
    • Comments: 0
  3. I

    Gauge Cluster Overlay Slipped?

    Heres a picture
  4. I

    Gauge Cluster Overlay Slipped?

    Will do... the anti-slosh module is a little card that often goes bad and causes the fuel gauge to read incorrectly... the needle either bounces (because of the sloshing in the gas tank) or it just doesn't read at all which is what happened in my case.
  5. I

    Gauge Cluster Overlay Slipped?

    Messed up blinker by Imatk posted Nov 16, 2016 at 3:44 PMI've had this issue for a while and wondered if anyone else had this problem and maybe knows a fix? My turn signals on the left look almost double... as if the overlay/backing has slid away from the hole for the light or something. How...
  6. I

    New Front And Rear Brakes Drums Rotors Shudder

    Thanks guys :) Yeah just crazy how one little thing can make a difference... now I'm annoyed that I replaced a perfectly good axle :/ But live and learn I guess.
  7. I

    New Front And Rear Brakes Drums Rotors Shudder

    So I'm feeling rather.. umm... ridiculous now. I THINK I've solved my problem. I tried one last time to adjust the shoes, but noticed the star wheel was a little tough to turn out sometimes and thought, "Maybe that wheel is not adjusting and dragging?" SO not only did I liberally lubricate...
  8. I

    New Front And Rear Brakes Drums Rotors Shudder

    Wheel cylinders haven't been replaced, but that will be my next step. To do the bearing I gotta pull the damn axle again... or so I think? The springs and shoes have been triple checked and they are on correctly and centered.
  9. I

    New Front And Rear Brakes Drums Rotors Shudder

    So I've gone through two sets of drums and shoes and replaced the axle... although I didn't replace the wheel bearing. Now I'm thinking I should have replaced the wheel bearing because it's STILL doing it. Other than the brake drag, the wheel bearing is silent but do you guys think that could...
  10. I

    New Front And Rear Brakes Drums Rotors Shudder

    Alright I'll go take a look, thank you!
  11. I

    New Front And Rear Brakes Drums Rotors Shudder

    Ok so I'm at a complete loss here. I actually replaced the drum and shoes on the passenger side, and it still binds. The driver's rear wheel turns freely but the passenger (the problem wheel) turns but noticeably binds at one spot. I checked the axle and it is SLIGHTLY bent, but like 5 one...
  12. I

    New Front And Rear Brakes Drums Rotors Shudder

    Thanks I'll see if it will drag when I get home from work tonight. I'll also check to make sure the shorter brake is in the front. So even a new drum would be out of round?
  13. I

    New Front And Rear Brakes Drums Rotors Shudder

    I didn't notice any grease... I can try and see if the axle moves though. Also this doesn't occur until the brakes have warmed up. When they're cold there is no shudder or noise.
  14. I

    New Front And Rear Brakes Drums Rotors Shudder

    So I have a fairly bad shudder when I apply my brakes under any kind of actual speed or load (like on a hill going down) and I thought it was just the car needing either front or rear brakes. So I just replaced the brakes. Rotors, Drums, Pads, Shoes. I'm still getting a shudder that's coming...
  15. I

    New Door Weatherstripping Door Won't Close/open

    Just replaced the weatherstripping on my 91 Mustang GT and now the doors are very hard to open and close. It's as if the weatherstripping is too thick. Is there a way to fix this or do I just have to go back to the old stuff? Thanks
  16. I

    Hatch Keeps Popping Open

    Thanks guys I'll give it a shot.
  17. I

    Hatch Keeps Popping Open

    I already replaced the bushing on the striker bolt... do I need to do something other than that?
  18. I

    Hatch Keeps Popping Open

    Are you talking about the striker bolt or a mechanism on the latch? I'm not too familiar with the mechanism.
  19. I

    Hatch Keeps Popping Open

    I've got a 1991 Mustang GT and my hatch keeps popping open when I go over bumps. I thought it might have been the bushing that had long since broken, but I replaced that and it's still popping open. Anyone know what I can do to solve this problem? Thanks
  20. I

    91 Mustang Gt Fuel Smell When Ac Is On

    Ok will do thanks!
Top Bottom
Back
Forums
Menu