Search results

  1. S

    Replacing rear spkrs on 95 vert with mach 460

    You can put a new speaker in there, look under the foam and there are four torx heads that hold it in, unbolt those pull speaker out, remove old wire or splice into it, run new wire and drop the new speakers in and you are set, just leave the factory tweeter disconnected. Let me know if you...
  2. S

    Can't get rid of interference noise

    Yup plug rcas into it the unit and the unit into the amp, make sure you do it at the amp side or else you defeat the purpose of the isolator. Good Luck Dan
  3. S

    Can't get rid of interference noise

    You can get a ground loop isolator which will kill lots of noise and see if that helps, sometimes a bad altenator will create some noise in your system, give one a shot Dan
  4. S

    Install ideas for Sirius plug-n-play unit?

    It works like a champ in the window, as long as it can see the sky you are fine, if it is under the metal then it does not work as good, I live in idaho we got lots of rural areas and canyons and trees and it works like a champ. Dan
  5. S

    Can't get rid of interference noise

    You got the power wires away from the rcas what about the grounds? If the rcas are near the grounds it will do the same thing, make sure that if the rcas cross the power or ground wires they do so as a T so they do not grab noise, make sure the ground wire is secured into the amp well and not...
  6. S

    Where did you install Sirius Tuner on 99+

    Is it a plug and play unit? If so see my pics a few posts down from this one, thats where i put mine to keep it looking clean with out putting any holes in the car, If it is a dedicated unit stuff it in the trunk somewhere out of the way and out of sight, you could mount it to the deck lid or...
  7. S

    Hooking up a Mono Amp

    You need a line out level converter, and then you grab 4 wires in the trunk, they are underneath the stock amp rack in a plug, black and black with green and black and black with white if i remember correctly, wire the level converter into those wires then rcas from there to the mono amp and you...
  8. S

    Install ideas for Sirius plug-n-play unit?

    It is the mach systems that are sirrius ready, if u got the standard cd player it does not have the sat radio feature. Dan
  9. S

    Install ideas for Sirius plug-n-play unit?

    Personally i would not go vertical, in the cupholder looks ok but it is hard to reach the buttons, and also hide all the wires, i have mounted them under the cluster before too, but again it is hard to make the wires all look clean. Mine is attached through the cig. lighter hole. What i did was...
  10. S

    Install ideas for Sirius plug-n-play unit?

    The xm antenna works great, i have the roady which is mounted in my pics, it looks real clean and does not looked tacked on there, and the best part is i did not have to put any holes in the car, i was quite pleased, the jvc unit is big so i would go with either the sportster or the audiovox...
  11. S

    Install ideas for Sirius plug-n-play unit?

    Pics of my xm unit installed Here are some pics of where i put mine so it was out of the way, let me know if you have questions and yes the antenna inside the back window works like a champ with full signal everywhere. Dan
  12. S

    Install ideas for Sirius plug-n-play unit?

    which unit Which unit do you have? I will take some pics of my xm unit for you, it would help if i knew which unit you had then i could give you some mounting ideas i used to be a install junkie and will do what i can to help. Dan
  13. S

    triple black

    Here is my old ride Dan
  14. S

    Help!!

    Doesn't the computer use the temp of then engine to determine when the engine is warmed up and go from there to control the engine parameters, I thought there was a set table it used until it was warmed up, no temp sensor the computer does not know what to do since it does not know how warm the...
  15. S

    Aftermarket radio with Mach system?

    The 99 mach system uses 3 amps and yes you can add a deck to it with the correct harness, the new mach system does not have a harness that works correctly. Dan
  16. S

    Aftermarket radio with Mach system?

    Dave> The mach system in the newer stangs is super ghetto, there was a harness for the older (pre 01) mach systems but there is not one that works correctly with the newer style. The new system has two amps that power all the 6x8 speakers and the factory headunit powers all 4 tweets, so you...
  17. S

    Needed new clutch again ,BTW Cobra clutch kit su#&$

    I was told that valeo was the original manufacturer of the ford clutches , and also makes a bunch of other brand names as well??? I used the upper end zoom in my 95 which was made by valeo it worked really well but again not something that would probally be considered a drag clutch. I have a...
  18. S

    Mach 460 info...

    They are 8 ohm speakers wired to give a 4 ohm load on the amp your non mach system uses 4 ohm speakers, and no you cannot switch you would have to have the mach wiring and the mach headunits, it would be very time consuming to switch over for what you gained. Hope this helps dan
  19. S

    mechanic in Idaho

    My younger brother knows a guy who does his tranny work for him and does a great job, also another guy that you could try is Restoration Rods by Rule, he owns a crap load of stangs, he is in eagle idaho. I'll track down the name of the guy my bro uses and let you know D
  20. S

    Feedback in my speakers :(

    That will do it, fix that and you should be a happy camper.
Top Bottom
Back
Forums
Menu