Search results

  1. R

    Got a coolant leak. Where is it?

    Waterneck, even the stock one will leak if the rubber hose isn't pushed all the way down and tightened right.
  2. R

    Code 332 Help

    I found some vacuum line from autozone help section, cost was like 2 bucks. The vacuum lines I mentioned are the one that go into the fender of the car, I felt the problem by removing the 2 of them closing the end hole and blowing into the other end of the line. This got rid of my check engine...
  3. R

    Electric noise back of car?

    I've had mine whine for about 6 years now. And car is still running.
  4. R

    Rear main seal

    I think it's the only way to do it!
  5. R

    Which Anderson Power pipe???

    You using a 75 mm tb ? in that case your better with the 3" pipe, since 75mm = 2.95" Heres a pic of mine, the fender has not been grinded yet, but I know I can get it better than this. [/IMG]
  6. R

    Which Anderson Power pipe???

    Actually you can get grind some of the fender out, and have no turns on the pipe or the couplers, less turbulance, as soon as the weather gets better i'll post pics.
  7. R

    Rear main seal

    I put in a TEFLON rear main seal on mine got in for 15 bucks at autozone. I put my rear main seal flush with the block, and it's working great, Don't forget thread sealant on the flexplate bolts.
  8. R

    Code 332 Help

    I had the same problem a long time ago. I replaced the EGR and still got the same code. The problem was those 2 plastic/tube lines that go into the fender.
  9. R

    Differential bearings

    Thanks for the quick reply, Im going to jack it up, as soon as my friend get's here i'll pin point the noise.
  10. R

    Differential bearings

    Here's the story. Whenever I raise the gar up on jack stands, and put the trans in "Drive, reverse, 1, second" and lightlly step on the gas I get a wooshing sound from under the car. Now when I get the car in the street, and drive it a little, no noise can be heard. Are the differential...
  11. R

    intake manifold questions

    Ditto. What im really interested in seeing is Brothers performance has a package on there magazines which they claim 30 something HP, changing only the: intake manifold (original performer), tb, and the pushrod lifters. \ BTW, I got my car running again, waiting until next week to get a temp...
  12. R

    Oil Pan Gasket Questions

    What type of gaskets do you guys use for the drain plugs on the oil pan ? vynil/plastic sold at the local parts store, or the ones with rubber that can only be purchased at Ford ?
  13. R

    Oil Pan Gasket Questions

    On a similar note: Would you guys recommend using rubber gaskets for the oil drain plug's (theres 2 of them, im pretty sure rubber ones were used from the factory) or can any plastic, vynil gasket be used for drain plugs.
  14. R

    engine to transmission plate is it important ?

    After looking at the number of views, and no responces, I decided to put it back, jacked the trans down, unbolted the flexplate bolts, put the engine plate in, thread locked the bolts, what a pain. Transmission goes back in next week.
  15. R

    engine to transmission plate is it important ?

    Gotta question is this plate really important, it goes between the flexplateto and the engine (where the trans is) I bolted up the trans already and found out I forgot to put this in there :doh: :bang: . say I instal some washers with the same width equal to the plate, will it work ...
  16. R

    people who have installed a Torque converter, need some help.

    If I could only edit my post from couple days ago. Tealstang, my torque converter hub is centered. The measurement I got from the mounting face pads (pads on torque converter that are bolted to the flexplate) to the bellhoising is .950 thousanths, really close to 1 inch. Which I should be ok...
  17. R

    people who have installed a Torque converter, need some help.

    1) Out of curiosity what happens when the transmssion pump bushing fails ? can you pull it out without opening the trans ? does it look worn out ? does it easily push up or down ? 2) out of this guide, my lenght For B = .805", and my length for A = .950" PATC's guide says Most Ford...
  18. R

    people who have installed a Torque converter, need some help.

    the second picture has the tranmission pump seal and the shaft that goes into the torque converter. I put a 6" ruller (pic) as far as I could into the transmission, and I wouldn't go farther than the 2" depth. my torque converter shaft is about 3". gonna try to install in again tomorrow.
  19. R

    electrical prob (headlights kill my car)

    Never heard of circuit protection before. How do you install it ?
  20. R

    people who have installed a Torque converter, need some help.

    I''ll give it another try, I can hear it whine when im pushing and rotating that last inch but that's about it.
Top Bottom
Back
Forums
Menu