Search results

  1. ChromdOutDubs

    408w Lives Again - Video

    Yea I'm running 2.5" now with the 1-5/8" primary. Like I said a 2" primary with about a 3-3.5" collector should let it breath a little bit better. The 351w swap headers are so expensive though.... -AJ
  2. ChromdOutDubs

    408w Lives Again - Video

    Yeah most likely i will be going to some Long Tubes with 1-7/8" - 2" Primaries with no mufflers for the track. I have 1-5/8 Shorties now and i know that's choking the motor down real bad. Any thoughts? -AJ
  3. ChromdOutDubs

    408w Lives Again - Video

    Well after about 3-4 months of rebuilding the tranny and doing a cam swap she fired up again today. The new cam is a Custom Grind from CamMotion. Its a .690in/.680ex lift, Lobe Center is 112 setup for nitrous. That should go good with the new fogger system that i got installed on the Vic Jr now...
  4. ChromdOutDubs

    Spool on street?

    I drove mine on the street with my full spool before I went full race. It wasn't to bad just driving around town. It does get worse when your trying to make tight turns in parking lots. You just have to remember to get rolling before you try to turn the wheels. -AJ
  5. ChromdOutDubs

    Kill switches...

    Found some... There are some pictures of mine located in the bumper. -AJ
  6. ChromdOutDubs

    Kill switches...

    I put mine into the back bumper. I will snaps some pictures for you tomorrow. -AJ
  7. ChromdOutDubs

    Intake Plumbed for Fogger Kit - Pics

    The fogger is still a wet shot since the fuel and nitrous are sprayed together. The fogger sprays to each cylinder equally unlike a plate kit or others where some cylinders might not get the same amount. 9.8's sounds good to me, ill be happy with 9.99's, as long as its nines its fine.
  8. ChromdOutDubs

    Intake Plumbed for Fogger Kit - Pics

    Going for 10's on motor, I'm on 2 tenths off from that now, and now i got a tranny brake and full suspension so that shouldn't be a problem. With the juice i want to dip into the 9's. -AJ
  9. ChromdOutDubs

    Intake Plumbed for Fogger Kit - Pics

    I sent my Victor Jr intake off to Steve Johnson @ Induction Solutions a few weeks back to get my Edelbrock Kit installed on it. He does some amazing work. I cant wait to get it installed and test it out, should be one crazy ride. I just got the motor and tranny dropped back down in the car. Just...
  10. ChromdOutDubs

    Flexing Pushrods??

    The thing that sucks is that the roller rockers are brand new out of the box, and the pushrods have like 10 track passes on them. I'm about tired of spending money on this car. Someone want to buy it? -AJ
  11. ChromdOutDubs

    Flexing Pushrods??

    The only pushrods i can find that are .120 wall are the ones that are 7/16" dia, and they have 3/8" ends. which means i would have to change rockers and guide plates.... -AJ
  12. ChromdOutDubs

    Flexing Pushrods??

    I am worried about it, its flexing enough that it will be a problem at 6500+ RPM's. I would say they bow out about 1/8th right at full lift.
  13. ChromdOutDubs

    Flexing Pushrods??

    Ok today i installed a new cam with a bigger lift than the last one. The old one was .620/.620 and the new is .686/.668. Well i needed to check the piston-to-valve clearance so i clayed the pistons. As i was rotating the motor over i noticed right when the rockers was getting to full lift, the...
  14. ChromdOutDubs

    baseline suspension

    Go to my old thread, i have pictures of all the components and the stuff installed on the car. http://forums.stangnet.com/749496-new-rearend-suspension-progress-thread.html Most of the people running this suspension stuff are the big horsepower turbo guys, and most of the faster guys out...
  15. ChromdOutDubs

    baseline suspension

    I have every suspension component they sell on my car. There stuff is awesome quality, and Kevin Slaby "The Owner" has helped me many times on suggestions on how to setup the car and get the suspension working like it should. I have their relocated uppers, with the larger heims, i have the...
  16. ChromdOutDubs

    pics of the new 347

    I was just curious how you knew, lol.
  17. ChromdOutDubs

    pics of the new 347

    How did you know he went with the other combo with out him even mentioning anything about it? Could you just tell from the pictures or am i missing something? lol
  18. ChromdOutDubs

    pics of the new 347

    Did you build the motor, or did you order the short block assembled already. Looks great.
  19. ChromdOutDubs

    5.0 Resto Carpet Kit Question

    Look up TokyoJoe on here. He has a deleted interior and it looks great. Mines also deleted and i made a custom panel to mount my switches and air/fuel, but mine has no carpet, ill grab some pictures of mine and see if i can find some of TokyoJoe's car too. EDIT: Here is TokyoJoe's car...
  20. ChromdOutDubs

    KOOKS make turbo headers now??!!

    Easy enough to make, looks to be some stainless shorties with the flanges cut off and v-bands welded in place. I'm sure kooks selling them for some ridiculous price though....
Top Bottom
Back
Forums
Menu