Search results

  1. bloopbloob

    Ok, ready for some more help with my clacking engine..

    ok thanks Foxfan88. would it help if i drained some coolant first then? and haha even the VC's took a BFH and a lot of prying and swearing just to come off (stupid cork gaskets with RTV!@#$*), so if you're warning me about this, i'm not looking forward to it! :rolleyes: and i was due for an...
  2. bloopbloob

    Ok, ready for some more help with my clacking engine..

    ok sorry for taking so long to reply. just in the middle of moving and some other stuff i needed to deal with first. but i checked every pushrod today, and they all looked fine to me. so now my next question is what do i need to do to remove the lower intake? pull the dizzy? fuel rails...
  3. bloopbloob

    can i re-use my upper to lower intake gasket?

    ok thanks. just wondering if after being compressed it was garbage or something maybe. it looks new other than that oil. no rtv on it or anything, i pretty much could have just breathed on it and it would have slid off... so i was wondering if it could be re-used. its maybe 2 years old, from the...
  4. bloopbloob

    stalling ?

    did you apply vacuum to the egr itself? i just stuck an extra silicon hose i had on it and sucked with my mouth to create vacuum, then sealed it with my finger, and it didn't hold vacuum. just out of curiosity, i did the same with the new one and it held vacuum. the diaphragm looked fine on the...
  5. bloopbloob

    can i re-use my upper to lower intake gasket?

    just wondering if i need to pick up a new one, or if this one is still ok? it looks pretty much brand new, except for the oil on the back runner holes, but just wondering if its still ok? and second, what would cause the oil on there?
  6. bloopbloob

    stalling ?

    before i even got to the part you wrote about your egr, thats what i was suspecting. i used to have the same problems with the car wanting to die when i was coming to a stop, or when rpms dropped quickly. ran the codes and got one for the egr. found out it wasn't holding vacuum, even after...
  7. bloopbloob

    Anyone else still gettin snow!???? this sucks

    haha well it blocked it on me for some reason.... try again... t-shirt hmmmm works now.... maybe i missed the r but i really don't think so.? :) ?
  8. bloopbloob

    Anyone else still gettin snow!???? this sucks

    like the title says... i'm so sick of canadian weather... shorts and t-shird (shirt is banned for some reason) weather yesterday, today there is almost 2 inches of snow on my car right now.... so stupid. just wonderin if anyone else deals with this crap.....
  9. bloopbloob

    Where is everyone?

    i call BS :bs: without pics of said GF!!! :D edit: hahaha please be gentle wis d bant stick! : )
  10. bloopbloob

    Headers Idea

    so YOU'RE the guy that buys the tornado! knew someone must have bought at least one of those things! :rlaugh: haha jk, but i couldn't resist:)
  11. bloopbloob

    oil pressure

    yup! i'm with the pump or bearings crowd. since it's rebuilt, that puts me on the pump crowd's side. only time i ever had oil pressure drop was when my bearings went. and i replaced them, and the oil pump (cheap insurance when doing a rebuild!!!) when it was rebuilt. no problems ever since.
  12. bloopbloob

    idle surges, gets choppy, then dies...HELP ME!!!

    Dump the codes! if you pull the codes you'd save yourself a lot of headaches and chasing problems you may not even have. on a side note, where has jrichker been? haven't seen anything from him in a long time!!! but yeah, usually, pull your codes and post them, and jrichker is a magical...
  13. bloopbloob

    couple codes, no CE light

    hmm... i'll see what other pics i can find for you... but iirc, all the outlets are the same color (black) and same size, and i think there are 5 outlets on that vac line... but i'm sure i have a pic of it somewhere, just not on teh interwebs yet. but i'll check for you. hang on a couple mins...
  14. bloopbloob

    couple codes, no CE light

    don't know if these will help, but here's a couple pics of the vac line that runs to the EGR. it is possible someone removed them completely....
  15. bloopbloob

    rear main seal leak?

    haha of course you have a rear main seal leak! you own a 5.0 mustang! :D seriously though, i've had to replace mine 3 times now, in less than 3 years.....
  16. bloopbloob

    Yaa, from the Mustang Chef

    haha at least this thread is actually going somewhere now! oh yeah? well watch this one! follow the moving circle with your eyes, then just look at the black + in the middle. oooooooooooooh!!!!!!!! hmm wasn't working when i came back, but here's the linky to a crazy eye trick thing...
  17. bloopbloob

    How to measure for gas shocks for the hood

    how are they being installed? welded on? bolted on? i've had to figure out how to mount shocks a few times, making (large industrial) custom toolboxes. it's kinda tricky and hard to explain how i did it though... do you already have the shocks, cuz that makes it easier
  18. bloopbloob

    couple codes, no CE light

    when my EGR went, it started causing problems like surging idle, & car would die sometimes when i'd come to a stop. i noticed better fuel economy after replacing it also.
  19. bloopbloob

    Yaa, from the Mustang Chef

    well you should go to bed! it's 4:22 AM here! (not sure about there) haha. jk. i'm drunk as a skunk right now too... :canada: edit: haha i never noticed how canada smiley winks till now! :rlaugh: haha lovin it!
  20. bloopbloob

    what to set timing at

    haha. that made me lol... maybe cuz its 4am and i'm kinda out of it, but nonetheless. haha!. anyways, yes, definitely set your timing with the car running. you'll have to pull the spout first (little grey thingy), loosen the dizzy bolt, then just slowly turn the dizzy to adjust it up or down...
Top Bottom
Back
Forums
Menu