Search results

  1. gregpro50

    Possible Tweaked Vert (Need Advise)

    If it is putting out 600hp with no reinforcements then maybe. The vert bodys will flex alot if not braced but it would be tough to bend one.
  2. gregpro50

    Possible Tweaked Vert (Need Advise)

    Yep it is. I'm not so sure it sounds like the uni-body is twisted. Sounds more like the hinges and hinge pins are worn. It takes a pretty good hit to twist the uni-body.
  3. gregpro50

    Hows this deal sound?

    He means was it converted to a roller motor.
  4. gregpro50

    Hows this deal sound?

    If it is a conversion car I would try to get it for less. Like maybe $2000.
  5. gregpro50

    89 Cobra or not??

    I understand that. The cobras were only made in '93. He is asking about an '89. No such thing as an '89 cobra.
  6. gregpro50

    Hows this deal sound?

    Sounds like a conversion car to me...
  7. gregpro50

    89 Cobra or not??

    It cant be a cobra. Even if it was a Canadian cobra like Michael Yount said it is cosmetic only. There is nothing in the vin # to separate it from a regular GT. Is your spedo in kilometers ??
  8. gregpro50

    how the heck do I install rear diff. upper bushing??

    :stupid: I did the same thing and they actually went in alot easier than I thought.
  9. gregpro50

    Rear Main Seal. Does it need to seat ??

    OMG did I luck out. After further investigation is seems that the crappy $50 chrome ebay oil pan didnt fit quite right to my surprise. All I did was tighten the oil pan bolts some more and NO MORE LEAK !! It must have been leaking from the back of the oil pan gasket. I'm going outside to do...
  10. gregpro50

    Rear Main Seal. Does it need to seat ??

    I cant tell exactly where it is leaking from because the tranny is in but it is definitley the rear main. I took my time putting it in and made sure not to scar the crank. I cleaned the surface all out on the block with prepsol and carefully installed the seal. The only thing I didnt do was...
  11. gregpro50

    Rear Main Seal. Does it need to seat ??

    Yes, it has a new Felpro seal. The original one was leaking so I replaced it. Now the replacement is leaking. I havent even run the engine yet. I sealed the threads to the crank and everything. I was thinking that maybe it just had to seat against the crank from running the engine a little ??
  12. gregpro50

    Rear Main Seal. Does it need to seat ??

    I have my car just about buttoned up after pulling the engine and redoing the gaskets. I put oil in the engine and noticed a small leak coming from the rear main seal. I havent even run the engine yet. Does the seal need to seat against the crank in order to work effectively ?? Also, I've...
  13. gregpro50

    Suggestions getting catback apart

    It works great. The passenger side is the bitch to do though. The GTs are a little harder cause the ground fx take away some of the clearance that you have to wiggle the pipes out.
  14. gregpro50

    KN Airfilters

    K&N filters are the way to go. I noticed a difference when I installed one in my car, truck, and even my atv.
  15. gregpro50

    Suggestions getting catback apart

    Drop the shocks and the quads and jack one side way up and the other way down and with some effort you can pull the whole thing out without cutting it.
  16. gregpro50

    Oil Pressure Fluctuates

    I had the same thing replaced by a mechanic on a car I owned and there was too much play between the crank and the bearings causing very low pressure at idle.
  17. gregpro50

    Oil Pressure Fluctuates

    Ummmm..... I'd be very worried then. Get a mechanical guage just to make sure but it sounds like a problem with the crank/bearings. Who did the work ??
  18. gregpro50

    Cant get O2 sensor back in!! What size tread tap ??

    IT WORKED !!! :banana: After a night of swearing and throwing tools I am so happy right now I could do cartwheels. The $5 spark-plug thread chaser worked perfect and it was probably something I should have in my toolbox anyway. Its interesting that the best tool that I have is my computer...
  19. gregpro50

    bent frame

    Well basically the uni-body is the frame and if you tweak something on the unibody you are essentially bending the frame. Same idea but the construction is a little different.
  20. gregpro50

    bent frame

    Just adjust the door. You can still have tight hinges and the door will be out of adjustment for one reason or another. Was the car hit to your knowledge ?? I have fixed quite a few cars that were hit before that I am perfectly comfortable driving. I wouldnt worry too much about it.
Top Bottom
Back
Forums
Menu