Search results

  1. G

    Engine (EGR Deleted) Solution the hotter combustion chambers?

    Somewhere around my shop here is 49 out of 50 of one resistor and 98 out of 100 of the other! If the wiring mod was happening to a transplant and you didn't want the connector hanging lose, it can be slodered i and wrapped up in the harness.
  2. G

    Need help 67 hazard flashers not working

    @THS70 Here are the results from a 1967 Mustang wiring diagram search. 1967 Mustang wiring diagrams
  3. G

    Engine (EGR Deleted) Solution the hotter combustion chambers?

    @PonyGTrider By the way, nice intake!
  4. G

    Engine (EGR Deleted) Solution the hotter combustion chambers?

    @PonyGTrider EEC-IV OBD1 you can do or make the tri-resistor circuit to make the pcm think that everything is intact. I didn't try that on my EEC-V controlled 5.0. I had to use the main EGR wire that feeds the pcm as a "wideband" o2 sensor wire that feeds the wideband reading on the "dashboard"...
  5. G

    Engine (EGR Deleted) Solution the hotter combustion chambers?

    My base is 10 but the program in the pcm has full control over what it is at any particular moment as it has to do with temp, rpms etc. I know this answer doesn't help much. I do know that if you make it too advanced it will run hot. Here is what google says: Yes, ignition timing that is too...
  6. G

    Need help 67 hazard flashers not working

    Now I'm not looking at a wiring diagram so don't hold me to this as fact or not. The same summer as my stroke, 6 years ago, I was working on a 1970 Mustang with hazard and signal switch issues. I kind of remembering an aha moment when, with a wiring diagram, discovered that the turn signal...
  7. G

    Engine (EGR Deleted) Solution the hotter combustion chambers?

    My most recent 5.0 has the "sonic" style EGR that has a passage through the intake instead of an external pipe. The passageway was clogged and the EGR valve has a vacuum leak. So I made a block off plate to go where the valve was and tapped the hole in the lower intake with a 1/2" pipe thread...
  8. G

    Power Pipe hole cutting methods....How'd you do it?

    Hole saws work great if it is a "virgin" hole that you are making. However, using a hole saw in to enlarge an existing hole is very difficult. If you were to fasten a scrap piece of wood or even 1/8" aluminum sheet to the back side of the existing hole, then the wood lets you make a new "pilot...
  9. G

    Brakes FOX BRAKES ISSUES

    Has anyone mentioned to check the condition of the metal (body) line going to the rear brakes? If it were pinched, it would result in reduced braking on/at the rear brakes. Just a thought. Thanks, guys, for all of hands-on information. There is a lot to think about as I upgrade my '85 to 5 lugs...
  10. G

    Non rev limiting cpu for 86 stang

    Gearing? ;) and sub $400 for a cpu, ecm, or pcm won't get you much. Save up your side gig money for this: Holley Terminator Max for Fox body Mustangs you will need several hundred more for the items that don't come in the kit. First, check to see if is legal to purchase and use in your state!
  11. G

    Winter fuel additive

    @Realmongo Alcohol. And I try not to drink gasoline if I can help it. ;) @manicmechanic007 Down here in the southeast, we have summer and winter blends too. That reminds me that I need to go start up one of my other older Fords and see if I can use up what it in the tank then put in 2 gallons of...
  12. G

    1968 DOHC 4.6 Coupe Project

    Well-built and a well thought out build. I hope to go page by page when we are snowed in and have some down time. You may have said somewhere in the thread about the AOD. Is it AOD or 4R70W (physically the same). Did you find yourself stripping the extra heat shields off of it to fit the early...
  13. G

    Winter fuel additive

    I see that the spelling error was corrected. I was making a joke off of that! @Noobz347. I don't drink...
  14. G

    Progress Thread Front Frame Rail Fixture ...and More

    Jim @horse sence I hope that you don't mind me asking this question here. I was always assuming that the front frame rails were on a parallel plane to the rockers. I see in your 1970 diagram that they are not. I'm working on a '66 and about to be working on a '65 also pulling on the front rails...
  15. G

    Winter fuel additive

    I need me some of that WINTER FURL additive!
  16. G

    Please!? I need some help with my 1964.5 alternator conversion

    I started researching it. There are some wiring harness differences not to mention, the difference between the generator and the alternator brackets. If a 1964.5 body was being built from scratch, you would use either a 1965 harness or if you want 5 dial instruments anyway, use a 1966 harness...
  17. G

    1966 mustang starter and pulley troubles

    @Realmongo I don't think that Hotrods4ray ever came back!
  18. G

    1967 Mustange Coupe

    @BadBev I guess that is the 4-cylinder Mercedes being the 240?
  19. G

    Mustang II V6 conversion to V8 HO and T5 problems and solutions

    I'm glad that you got the exhaust manifolds figured out. The mid late '60s Mustang manifolds appear to work well.
  20. G

    Mustang II V6 conversion to V8 HO and T5 problems and solutions

    I'm a little late for the party. If you want to go to standard rotation water pump, forgive me if this has already been covered, you need a mid to late 1970's timing cover. It has the spot for the mechanical fuel pump. You will need an eccentric (a disc or wheel mounted eccentrically on a...
Top Bottom
Back
Forums
Menu