Search results

  1. 3

    K&N FIPK II should I get it

    I need more proof that it works.Dyno sheets anyone besides trinity GT.
  2. 3

    Steeda N/A tune Dyno results

    Mine were 242Hp and 282TqSAE corrected.Who has results from their tune.03 GT steeda tune ,U/D pullies 3.73 gear,Flows,FMS70mm TB,TFS intake.The car ran lean down low till about 4,000 rpm then ran 13.1 and 12.7 on second pull.I think I had a vaccum leak.so back to the dyno I go.Anybody have...
  3. 3

    Car ran lean on dyno

    Anybody know what the numbers are uncorrected?
  4. 3

    Baseline Dyno Tomorrow

    Good numbers, seems really high,did you run air/fuel? Mine were 242Hp283 Torque SAE
  5. 3

    Car ran lean on dyno

    wide band 02.Thats all I know.
  6. 3

    Car ran lean on dyno

    Come on guys anybody go lean from mods
  7. 3

    Car ran lean on dyno

    I checked for leaks vacumm is at 20in. Im faxing the dyno sheets to steeda so they can help out.Am I the only one that thinks 241 is low for what I have?
  8. 3

    Car ran lean on dyno

    I went to street stuff in addison ill. and dynoed a03 Gt 5speed with TFS intake, Ford 70mm TB ,U/Dpullies ,steeda N/A tune,Flowmaster mufflers. the car dynoed at 241hp and 282 tq.the a/f is 15.9 at 3200,and stays at 15.5 till4300 rpm . At 5100rpm its at13.7.the second run is the same. My...
  9. 3

    Trick flow whistle

    I have the FRPP 70mm.
  10. 3

    Trick flow whistle

    Just installed the TFS plenum.But on throttle tip in theres a whistle.The car idles great,good throttle response.No codes.the car has 1800 miles on it all gaskets new.Anybody else have this.I noticed theres atear drop inside the old intake above the EGR hole.Im wondering if ford put that there...
  11. 3

    steeda tune questions

    Ive got the steeda tune,3.73.It works well, better than any chip Ive ever used.Ive used superchips ,diablo both sent back countless times.For a bolt on car steeda is the way to go.If your considering cams the car has to be tuned on the rollers.
  12. 3

    Mustang GT vs WS6 Trans AM!!!!!!

    My 02 Z28 A4 2.73 geared car ran 13.0 at 108mph.My 03 GT 5speed ran 14.0 at 98mph.You may get out of the hole first but it will reel you in.Race in the 1/8 it will be closer.BTW 02 had a lid and cutout.The Ls1 is just quick,BUT they are quicker to fall apart.Needle bearing fellout of the rocker...
  13. 3

    tri-ax, low or high?

    High for comfort driving,low for aggresive shifting. mine is high.On the low setting Im working to shift.
  14. 3

    How to Correct Eibach Spring Sag Problem

    Try spring spacers steeda sells them each spacer raises the height .25inches.
  15. 3

    Hey, at what rpm do you guys launch?

    2,000rpm slowly releasing the clutch.
  16. 3

    Chevy guy considering a Mustang....... come help.

    I had a 02 Z28 A4 2.73 and ran 13.0 at 108.Fast for a stock car. But it was faster to fall apart.Found needle bearings in the oil pan from the rockers.Needed a new motor.I loved the speed the car produced, the power 311 at the wheels,but I forgot all that when the motor started ticking.Now I own...
  17. 3

    New Member - Just Bought 04 GT

    Chan are you trying to be funny?
  18. 3

    New Member - Just Bought 04 GT

    Theres a TSB on the guides. theres atick on the left head.The head gets replaced. I stated some run 13's not that it doesnt happen.
  19. 3

    New Member - Just Bought 04 GT

    They dyno at 230-235rwhp. Run low 14's high 13's(very few) and have noisy valve guides.You can weld in flowmasters for around 200 dollars.Mufflers of anykind give sound and very little HP.
  20. 3

    My 3.90's aren't that great.

    Disconnect the speedcal.Your Ecm runs off the VSS.
Top Bottom
Back
Forums
Menu