Search results

  1. R

    96 Cobra Oil Leak Bad

    well it looks like no one makes a new oil cooler that is factory, i find them use for $180-$350 on ebay and mps auto salvage. i mite call a few local junk yards. is that pin hole suppose to be there?
  2. R

    96 Cobra Oil Leak Bad

    My cobra is leaking oil behind where the oil filter goes on, it has a small pin size hole on the adaptor, plus it’s leaking at another spot it looks like on the adaptor as well. Is that an adaptor that comes off or what? All post some pics. I got the spots that are leaking circled on the pics...
  3. R

    Brakes The Ultimate 4-lug/5-lug Brake Conversion/upgrade Thread

    im using 91 v8 fox brakes on my 86 4 cyl. what hydro boost and mc should i run?
  4. R

    Swaping 4cyl Front Suspension For 5.0 Problems

    no there does not seem to be.
  5. R

    Swaping 4cyl Front Suspension For 5.0 Problems

    the pic in the middle is the other side i have not messed with yet, it has the rivet in the middle hole
  6. R

    Swaping 4cyl Front Suspension For 5.0 Problems

    ok you can see here in the 1st pic, where i have my chisel point at that is the hole that was riveted before i took off that bracket. now i would think i would have to get it to aline with that hole.
  7. R

    Swaping 4cyl Front Suspension For 5.0 Problems

    its not all post up some pics here then
  8. R

    4 cyl vs GT suspension

    i need help im swaping the front suspension from a v8 car to my 4cyl, the only problem i have ran into is the shock mount at the top of the shock tower. it seems that i will have to grind down the hole where the shock goes throu to get it to aline right. is this normal?
  9. R

    Putting On K&n Directly On Mass Air

    thanks guys all just take the k&n back then
  10. R

    Swaping 4cyl Front Suspension For 5.0 Problems

    I’m putting the hubs, brakes, and shocks from a 90s 5.0 on my 1986 lx four cyl. I’m having trouble with the shock lining up right in the shock tower is this normal? I took off the bracket that is riveted in to the top of the shock tower and I can get the new shock to go thru but can’t get the...
  11. R

    Putting On K&n Directly On Mass Air

    I put a k&n filter on the end of my mass air meter on my 1988 mustang, the mass air meter is a stock one off of a 90's stang. Well since I put it on some times the car will idle rough and it runs a lot leaner than it used to when I just drive normal. I have an aem wide band to measure a/f...
  12. R

    Ball Joint Replacement 86 4 Cyl

    nvm i got it
  13. R

    Ball Joint Replacement 86 4 Cyl

    do the ball jounts on these press out like other mustangs or are they built into the lower control arm in the front? lmk asap thank you
  14. R

    O2 Wiring

    so since my new o2 wiring has the light blue that gets looped i cant use it on my aod car?
  15. R

    Electrical E-fan... Pulls Sooo Much Amperage. Help?

    is this a dcc http://www.dccontrol.com/selector.htm ? what one would be good for a 98 v6 contour fan? im using a spal right now in one of my cars and like it, but it is alittle on the expensive side... but so is that dcc.
  16. R

    O2 Wiring

    does any one know if this will work? http://www.autozone.com/autozone/parts/Bosch-Oxygen-Sensor/1988-Ford-Mustang/_/N-ihy8aZ9ixrp?itemIdentifier=282408_168323_16521_
  17. R

    O2 Wiring

    i also notice that where the o2 connector plugs into the engine harness only has 5 pins on it aswell. i have a newer engine wiring harness that is off of a mass air car and it has all 8 pins where the o2 connects to the engine harness.
  18. R

    O2 Wiring

    I burnt my harness on my exhaust and need help. I have 3 o2 wiring harnesses. Two are different from my original. My car is a 1988 mustang with a aid and has a mass air swap. Ok my original harness only has 5 pins that come off where it hooks into the main harness. The color codes on the wires...
  19. R

    4 Lug Rear Disk Swap From Tc

    i seen a 1987 tc in the junkyard that still had the rear brakes and all on it i just want to know what do i need to swap them to my 1988 mustang gt.
  20. R

    4cyl To 5.0 Swap Help

    what do i need to get it to work?
Top Bottom
Back
Forums
Menu