Search results

  1. HoofnIt

    Winshield

    FYI-I have a new-edge 'pony' winshield in my 95 stang. They WILL fit but it's VERY close. The main difference is where the lower cowl edge of the glass meet the cover. It BARELY covers but it will cover. I had more than one company tell me that it wouldn't fit but finally got someone to try...
  2. HoofnIt

    Well this blows, wrecked my car :(

    Sorry to hear about that. I'm glad you're OK, it could have been much worse huh?
  3. HoofnIt

    Congrads to Oink!!!!!!

    I haven't seen/heard much from him lately. I guess he's been busy. Way to go!
  4. HoofnIt

    95 Factory Cobra Intake

    With a HCI I would only recommend getting the lower ported. That will improve the flow and save you a few bucks compared to a new intake.
  5. HoofnIt

    How to swap tranny drive gear for speedo?

    Update: I finally got around to attempting to swap out the DRIVE gear on my tranny. First of all, I would like to say that this was NOT as easy as described in the reply I posted from the Corral. I had to take the tranny out anyway because of an oil leak which I thought was from the RMS-more...
  6. HoofnIt

    Head gaskets installed backwards???

    I can't tell if the tabs are on the front because there's too much CRAP in the way! I guess I'll have to take the alternator off to see on the pass. side. I don't know about the driver's side. I am in the process of dropping my tranny to replace the rear main seal so I think I will have a...
  7. HoofnIt

    Speed Cal .... or not?

    As far as the speedcal you need to know what your rear gear ratio is and the ratio your speedo gear is for. For example if my speedo gear is for 2.73 and I switched to 4.10s then I will use the speedo gear (2.73) to look up the first binary code. The second binary code will correspond to the...
  8. HoofnIt

    My headlights suck

    Sorry to hijack but are the Sylvania SilverStar's worth the money? Will you really be able to tell a difference?
  9. HoofnIt

    Speed Cal .... or not?

    Dallas Mustang's website says the SpeedCal will work for 94-04. The driven gear in the tranny mechanically turns the speedo gear which mates to the Vehicle Speed Sensor which is electronic. There are multiple electrical wires that connect to the VSS.
  10. HoofnIt

    Long tube header question...

    Thanks for the replies guys! :D I think zenboy had the right idea. I was wondering how difficult it would be to change out a clutch with the longtubes in place? I would hate to remove the headers just to drop the tranny. Would an x or h-pipe be better with the longtubes or is there much...
  11. HoofnIt

    Long tube header question...

    Those of you who have long tubes, do you have to remove the headers in order to take the tranny out? I have shorties and am contemplating stepping up to long tubes but I'm wondering what kind of headaches go along with them? THX
  12. HoofnIt

    Head gaskets installed backwards???

    Eric94GTvert-are you talking about the front or back of the head? I'm guessing the front...hmmm
  13. HoofnIt

    Head gaskets installed backwards???

    Last summer, 2004, when I did the HCI I installed new upper and lower radiator hoses, new 180 tstat & new FRPP waterpump. This past summer I had the coolant flushed, I already have a Fluidyne, and I also replaced the electric fan two months ago. Normally 200 wouldn't be so bad but here in...
  14. HoofnIt

    Head gaskets installed backwards???

    What would the symptoms be if the head gasket's water ports did not line up right (the front was towards the back)? I mean I know that this would compromise the flow of the coolant but how hot would it run? Has anyone had this happen to them? I'm not an expert in this area but my car runs too...
  15. HoofnIt

    Will 93 Valve Covers fit a 94?

    I'm running the fox valve covers with stud-mounted rockers and a Cobra intake and NO spacer. This required grinding down the lower portion of the EGR mounting surface, grinding down the front of the pass. side valve cover to make room for the alternator. I also had to remove the oil fill...
  16. HoofnIt

    How to swap tranny drive gear for speedo?

    I did a search on corral and came up with this reply: Its not hard to change the Speedo gear on the outout shaft. All you do is undo the rear case, and drain the tranny fluid out, then take it off and its right there, should be black, if you have 3.08's. You get the white one from any ford...
  17. HoofnIt

    How to swap tranny drive gear for speedo?

    I'm sure someone here has changed this drive gear before. Anyone...Anyone?
  18. HoofnIt

    How to swap tranny drive gear for speedo?

    Does anyone have a link to a how-to for this? I finally picked up the right parts and was wondering if anyone had any tips or instructions. Thanks.
  19. HoofnIt

    What clutches you guys running

    I'm running a SPEC I with no problems. Pedal feel is really good and even with my 4.10s and 290hp it's holding real well.
  20. HoofnIt

    Idle Probs, Yeah Ive done everything the search engine suggested, still need help

    It really sounds to me like your problem is with the distributor. After my HCI it took me several times to finally get that stupid thing in there right. I know this may sound redundant but I would check all of your electrical connections. I also found out after much frustration that my MAF...
Top Bottom
Back
Forums
Menu