Search results

  1. tvmango

    can you install engine with longtubes and bellhousing installed??

    I see engines in old post built on the stands with the longtubes already on the heads,, can you install the whole engine that way? With the bellhousing also?? It fits?? thank you ,, tony
  2. tvmango

    air/fuel ratio gauge install????

    bro i found it!!! http://www.autometer.com/hp/techtips/air_fuel_hookup/air_fuel_hookup.html
  3. tvmango

    please help with clutch fork ball pivot height ????

    ttt
  4. tvmango

    does someone have a picture of their upr a/c delete pulley installed???

    Am I just a idiot or what?? I can't figure out how this goes on, and there is no directions on their website....I figured out the smog pump pulley easily, but this is just weird.... tony
  5. tvmango

    please help with clutch fork ball pivot height ????

    ttt,, please guys...
  6. tvmango

    air/fuel ratio gauge install????

    I also need to know this... subscribe..
  7. tvmango

    please help with clutch fork ball pivot height ????

    I have a Mcleod BH and need to set the ball stud height, Every old post I found in a search just tells people to measure the stock bellhousing pivot ball hieght and go from there... Well i don't have a stock bellhousing to go by,, so if anyone knows, or could measure one for me on a bellhousing...
  8. tvmango

    Tremec... Best place to purchase?

    jeff at nitrostangracing.com hooked me up.....his email is [email protected]
  9. tvmango

    who has a 331 d.s.s. ?

    All of this is here say,, I can't believe tom , the owner of dss wouldn't talk to him,, He has alway been there to answer every ? or prob I've had.. Did you guys break it in properly?? Over rev it?? Did all of these bad motors have the old style probe pistons they used to use, that they had...
  10. tvmango

    dumb ??? where is a good place to lift my motor from with alum heads???

    that would scare the hell out of me!!! the bolts that hold on the upper are sooo small...
  11. tvmango

    Tilt into a non tilt car...

    It is completely legal to remove your airbag,, but it i not legal to sell it that way... I have done it in my dealership.....
  12. tvmango

    P/N for the rear plugs for heads

    it should.... are your holes are course tread, and will a spark plug almost screw in (by hand) but not really fit? If so they should fit... Search through some of the old posts in here, I remember seeing the ford part # your talking about,, but is that for cast heads???
  13. tvmango

    dumb ??? where is a good place to lift my motor from with alum heads???

    coool, thanks again,, tony
  14. tvmango

    dumb ??? where is a good place to lift my motor from with alum heads???

    hey mike 2 ?'s, how do you like the jegs roll cage? and what did you use for a smog delete?
  15. tvmango

    dumb ??? where is a good place to lift my motor from with alum heads???

    thank you mike.. I will do that...
  16. tvmango

    P/N for the rear plugs for heads

    TFS-51400265 is the trick flow part #,you can get them through summit like i said above, after seeing that picture, spark plugs may work on cast heads, but it stripped my alum heads, I had to get the above to make it right..
  17. tvmango

    dumb ??? where is a good place to lift my motor from with alum heads???

    ok,, I really didn't feel comfortable with the little header holes in alum!! ,, I will use those bigger end holes,, thank you bro!!
  18. tvmango

    P/N for the rear plugs for heads

    I tried the saprk plug thing and they strip in not thread in, they are a course thread, 5/8-11,, summit has them for 3$ each...
  19. tvmango

    Tilt into a non tilt car...

    It will work fine, i did it in my last mustang and ditched the sh-tty airbag steeringwheel, cause the little bastards stole my car and f-cked it up on me,, like said aboir by rob you will have to change a bit of the wiring cause of the switches are different,, my cruise woildn't line up, so i...
  20. tvmango

    dumb ??? where is a good place to lift my motor from with alum heads???

    I just don't want to kill anything, I assume I will have to buy one of those things to angle my motor while lifting it (trans on).. But where do you bolt the chains on? I cant put the stock engine pulling tabs on or they will hit my heads,, I could make it work by "rigging" it, but I figured I...
Top Bottom
Back
Forums
Menu