Search results

  1. L

    Transmission Reccomendation Help

    The convesion is pretty straight forward, the auto is just much heavier then the stick so an extra hand is a good start. Instead of buying a new radiator for the cooler lines you and just pick up a nice tranny cooler and mount it infront of the existing radiator or something. You will need...
  2. L

    Any tips? Installing Springs, Shocks, Subframes, control arms this weekend.

    +1
  3. L

    Stock Auto Shifter replacement suggestions

    The B&M Hammer is a real nice shifter, I had it in my car for 3 years before going stick.
  4. L

    T-Bird SC Eaton Charger.....

    I have seen that done before. There is a local mustang performance shop around me that did that set up on a fox. I never saw the car run personally but supposedly it made some good power with it.
  5. L

    Car Runs Really Hot

    :nice:
  6. L

    Car Runs Really Hot

    Is your fan turning on when it's supposed to and staying on? I tried one of those automatic fan sensors before and found the thing to be garbage.
  7. L

    Vert Top Frame

    Hey everyone, On my vert when I put up the top it is a complete struggle to get the latches to line up, and once the top is finally locked down there is a pretty good gap between the top and windshield frame on the corners. Is there anyway to adjust the frame other then just unscrewing the...
  8. L

    clutch pedal assembly

    :nice: .... and before you begin make sure you are very relaxed and not stressed from anything else... cause soon as you start you will be pulling your hair and ready to throw the car off a cliff or something haha
  9. L

    New T5 short shifter.. Which One???

    I have the Steeda Tri-ax and I love it
  10. L

    wont idle when cold....

    My car had the same symptoms before and it turned out to be the Air Charge Temp Sensor, the sensor was all gummed up, once I changed it the car ran great from a cold start.
  11. L

    2.3 t5 on a 302???

    The pilot bearing that you need is p/n 14672 at AutoZone.
  12. L

    T-5 Input

    Alright, thanks for the input. I will have to take an AutoZone trip and pick up that pilot bearing. I wasn't sure how much abuse a 4cyl t-5 could take, I didnt know if being behind a v8 the first time I dropped the clutch it would just rip itself apart or what.
  13. L

    T-5 Input

    Hey everyone, I'm on a budget build and I have a 4cyl T-5, to make this thing at least some what stronger until I can afford a tremec or somthing of the sort can I use an Input shaft from a 5.0 t-5 or would I end up having to swap out the entire gear set? I believe that all the 4cyl t-5's...
  14. L

    Choosing an Intake???

    It is a original upper with a gt40 lower. I'm kind of confused with it though, the ports on the head side of the lower are slightly smaller then then ports on the actual heads, prior to this intake on my old set up I had a Trick Flow street heat intake and the ports were huge in comparison to...
  15. L

    My project has come to a halt - found wheel locks on rims and i dont have a key!!!

    Snap-on sells a tool kit thats specifically used for removing wheel locks....
  16. L

    1/4 mile

    Oh yes, I have long tubes with 2.5 off road h pipe and cat back. Last summer I went 13.6 @ 104 with: Exhaust Gears Intake/65 mm Throttle body Underdrive pullies Cobra R's I was hoping that the extra mods this summer would put me in the high 12's but I guess that was to high of hopes.
  17. L

    1/4 mile

    Toyo Proxes 4 245/45
  18. L

    1/4 mile

    Hey everyone looking for an estimate on what my car should run once I finish putting it together. 90 Lx Vert 5.0 302 Bored .030 9.5:1 c/r Stock heads ported with GT40 valve package E303 Cam 1.6 Full Roller Stud mount rockers Cobra Intake 65mm throttle body 24 lb/hr injectors 76mm...
  19. L

    Choosing an Intake???

    Hey everyone thought I would make an update to the intake situation. This week I picked up a nice clean cobra intake for 75 bucks.
  20. L

    Choosing an Intake???

    Would the RPMII rob a lot of low end torque? There is one for reasonably cheap in the classifieds of the local auto mag. so I thought about picking it up unless it would do more harm then good to the power.
Top Bottom
Back
Forums
Menu