Search results

  1. krahkin

    Anyone brake their clutch cable over and over and over and.....

    Have you thought about using a pedal stop to prevent breakage?
  2. krahkin

    A/F Guage Question

    I am installing an air/fuel guage in my 95 and have run across a slight problem. The directions with my guage do not specify, nor can I locate it in the Hayes manual, which of the 4 O2 wires I need to use for my guage. It should be the 0-1V wire. With my voltmeter, I have narrowed it down to 2...
  3. krahkin

    Upgrading to 9 psi?

    Change to a smaller pulley on the head unit. Powerdyne's arent made to handle anything over the 9lb pulley. Most folks dont remind you of this, but if you have a good breathing engine, your boost guage wont or shouldnt read 9lbs. 9lb of boost on your guage is the backpressure, not the flow rate...
  4. krahkin

    Speedometer gears

    There should be a 19-tooth gear in your stock configuration. Why not just get a SpeedCal? That way when you change tires, gears, etc. you can just flip a dip switch and have stock accuracy. Yes, I run one. :D
  5. krahkin

    Power steering pump noise (fix?)

    Go to Advance and pick up a bottle of Pyroil power steering fluid. Mine used to be loud too :D
  6. krahkin

    Need opinions on rearend buildup

    The Eaton unit is beefy, but may not be your best bet for a daily driver. An Aubrun would be a well-suited fit. Also, if you do drag your car as well, you may consider the new Ected (I think Auburn makes it?).
  7. krahkin

    289 HiPo vs 390

    IMO the 390 would be hard to beat. The only motor of that era that I would take over it would be the 351C.
  8. krahkin

    Cam lope...what cam lopes like this?

    B303 cam has a lot more lope than E if that is all that you are looking for.
  9. krahkin

    Anyone ever heard of this BXR intake on ebay.

    The new BBK intake is very similar to this one, if anyone is interested in owning a dual plenum intake.
  10. krahkin

    CAUTION: Enter only if you wanna go FAST.

    Let's see some dyno numbers!
  11. krahkin

    Help With Some Upgrade Ideas

    I know a lot folks that run the E cam in my area. I have no experience with either so I cant really say. As far as gears go, I strongly recommend 3.73's.
  12. krahkin

    Black Bullet Rims

    gcomfx.com, I run 10.5 out back with 315's. They are my 2 cheapest tires. Go figure.
  13. krahkin

    Just installed TW heads and now have HUGE problem with pinging realy bad

    Did you have your pistons notched for the TW heads?
  14. krahkin

    5.0 Miata - WTF

    There a guy in a nearby town down here that has a Pontiac Fiero (remember those?) with a chevy 350 stuffed in it. That thing is sick.
  15. krahkin

    South Carolina

    You can always come over to Georgia. We have lots of counties that are Mustang friendly :rolleyes:
  16. krahkin

    Header Install

    Im with HairyCanary on this one. I had to bend the bracket a tad, right at the fork which hugs the header bolt. Have fun with the new LTs! :D
  17. krahkin

    Are 4.10 worth the extra $400 than the 3.73 on an aode????

    Just wanted to point a few things out. 3.55's are the highest gear ratio you can run with only a speedo gear change (and still be accurate). I use a Dallas Mustang SpeedCal in my 1995 5-speed with no problems. It is accurate within .1 mph. The install only took an hour or so, and to me was well...
  18. krahkin

    AFR People???

    94-95 Cobra Intake that has the lower ported by TMoss (no, I havent sent mine yet, but I fully intend to do so!). He told me he can flow the cobra within just a couple CFM of the 165s.
  19. krahkin

    95 GT vs 2004 EVO

    Evidently, the Brembo brakes are stock. When I bought my wife's Montero Sport, there were 2 Evo's in the showroom. Needless to say, I couldn't resist checking them out. Both had Brembos up front, Recaro seats, etc. As far as the price, around here they average around 27-28k new, no where near 38k.
  20. krahkin

    Drag Day Silver Dollar Raceway Reynolds, Georgia All are welcome!

    Bah I didnt get to make it, although I'm close to having my engine finished. Any more times to be posted? :D
View older results
Top Bottom
Back
Forums
Menu